Kansas State University Research and Extension
Introduction
What's Inside?
Lesson 1 Take Control of Your Own Safety
Lesson 2 Prepare for Safe Operation
Lesson 3 Preventing Rollover Accidents
Lesson 4 Avoid Being Caught in Moving Parts
Lesson 5 Other Common Dangers
Lesson 6 Environmental Hazards
Conclusion
Quiz Yourself Solutions
This booklet teaches important safety practices to follow when mowing. You may use a wide range of equipment including:
- agricultural mowers
- riding lawn mowers
- walk behind mowers
- string trimmers
- brush trimmers
Safety tips, along with real accident reports, have been combined to give you a better understanding of the risks associated with this type of work.
Use this booklet in conjunction with hands-on safety training and the equipment operator's manual.
- Name the most common types
of serious accidents involving
mowers and trimmers.
- Interpret the meaning of common
warning signs and labels.
- Identify appropriate protective
equipment.
Failure to observe safety precautions when operating mowing equipment can result in serious injury or death. The most common types of serious accidents are:
- Rollovers
Agricultural mowers and riding lawn mowers can overturn,
causing injury and death.
Accident Report
Operator Crushed by Riding Mower |
Summary of OSHA Accident Inspection 107975153
A worker was operating a riding mower on a hill. He was mowing too fast and made a sharp turn, causing the mower to tip over. The mower landed on top of him, crushing his rib cage, puncturing his lungs and killing him. Never make sharp turns at high speeds, especially on a hill.
|
- Being Caught in Moving Parts
Serious injury or death can result from being caught in mowing equipment's moving parts.
Accident Report
Employee Loses Finger While Lifting Mower |
Summary of OSHA Accident Inspection 119815108
An employee was operating a riding mower in a parking lot. The mower slipped off the curb. Without shutting off the engine, the employee and a coworker tried to lift the mower. One of the employees put his hand under the front of the mower and lost three fingers at the first knuckle. Never put hands or feet under a running mower. Always shut the mower off before servicing.
|
Safe work habits are important. Here are three actions you can take to be safe on the job site.
- Learn all you can.
To prevent accidents with mowers and trimmers, read and follow
directions in the equipment operator's manual. Pay attention to safety instructions in the manual and to warning labels you see on the equipment. If you have questions, stop and ask your supervisor before you continue.
- Concentrate on working safely.
Sometimes you may be tempted to take risky shortcuts. Remember
that an accident can leave you permanently injured
or cut your life short. For your safety and the safety of those
around you, do not take unnecessary risks. No deadline is so
pressing you can't take the time to do your work safely.
- Additional Precautions
Do not operate machinery if you are tired or have taken drugs or
alcohol. If you are on medication, discuss with your doctor or
pharmacist if you are capable of safely operating machinery.
Manufacturers put important safety messages on mowing equipment and in the operator's manual. It is critical to read, understand and follow all safety messages.
The triangle shape is the symbol for caution. The exclamation mark in the center means Pay Attention. In some instances, the triangle-shaped sign will show a picture. Other times, words explain why the sign is used.
Many safety messages use the words Caution, Warning and Danger to get your attention. Following are safety messages and their meanings. Each of these signs will have a written message, and perhaps a picture, about an unsafe condition.
CAUTION means you need to be careful. Follow the directions on the sign or you could get hurt.
WARNING is more serious and means you need to follow the directions on the sign or you could be badly hurt or killed.
DANGER is the most serious safety message. If you don't follow the directions, you will be seriously injured or killed.
Images displayed in the caution, warning and danger boxes have been recreated from images taken with permission from ASAE S441.4 FEB04, Safety Signs.
Certain equipment is necessary to protect your body from materials ejected from the mowing equipment and from being caught in moving parts. When operating mowing equipment you should wear the following.
Close-Fitting Clothes and No Jewelry
Loose shirt sleeves, pant legs or jewelry can catch in the equipment's moving parts or on electrical lines, resulting in injury; therefore, close-fitting clothes should be worn. Pull back long hair.
Long pants and sturdy, non-slip boots.
Wear long pants, and sturdy, non-slip boots to protect your legs and feet from objects that are thrown from the mower. Never wear sandals, which expose your feet, or tennis shoes, which can easily be severed if caught under the mower deck or in the trimmer's cutting swath.
Safety glasses and a face shield.
Safety glasses should be worn at all times unless operating equipment with an enclosed cab. A face shield should be used, in addition to safety glasses, when operating a string/brush trimmer and other times when your face could be hit by debris
Accident Report
Employee's Eye Cut by Flying Debris |
Summary of OSHA Accident Inspection 119806867
An employee was mowing grass with a tractor, but was not wearing safety glasses. He looked back and a piece of metal was thrown from the mower and punctured his right eye. He lost all vision in that eye.
Always wear eye protection when operating all mowing equipment.
|
Hearing protection
Over time, you will lose your hearing if you are exposed to loud noises without protection.
Two common types of hearing protection are muffs and plugs. Ear muffs should seal around your ears to properly muffle loud noises. Wash reusable ear plugs with warm, soapy water after each use in order to prevent infection. Discard disposable ear plugs after each use. When to Wear Hearing Protection
OSHA Standard 1910.95 (i) (l) requires hearing protection to be worn when sound levels exceed certain limits (generally, a daily average of 85 or 90 decibels, depending on the circumstances). These levels can be measured with a sound level meter. A hearing conservation program requiring hearing tests and other precautions may also be necessary. Check with the equipment operator's manual, as well as your supervisor, for suggestions on hearing protection for each piece of equipment and instructions on how to wear it properly.
Hearing Protection Rules of Thumb
Hearing protection may be needed if:
- You have to raise your voice significantly to be heard by someone three feet away.
- After leaving a noisy area, your ears feel plugged or you hear a mild ringing or whooshing noise that goes away after an hour or two.
- When you start your car in the morning, the radio is so loud from the evening before that you have to turn it down.
Circle the correct answer.
For answers, click here.
- What are the two most commonly reported causes of serious injury and death from operating mowers and trimmers?
- Rollovers and being caught in moving parts.
- Heat stroke and lightning strike.
- Carbon monoxide poisoning and burns.
Select the correct answer for the following sentences from the list below.
a. Danger
b. Safety glasses
c. Alcohol
d. Caution
- The triangle shape is the symbol for ___________.
- _________ should always be worn when operating mowing
equipment.
- Never operate any type of equipment under the influence of
________ or drugs.
- __________ is the most serious safety message.
Choose the correct answer.
- When operating mowing equipment, it is important to wear clothes that are _________________.
- Expensive
- Close-fitting
- Ironed
- Wear _______ to protect your feet when mowing and trimming.
- Sandals
- Tennis shoes
- Sturdy boots
- Indicate mower parts to be inspected
before operation.
- Identify steps to prepare the
area for safe mowing.
- Recognize safe start up and
shut down procedures.
Safety starts before the engine. A thorough inspection of the mower or trimmer is important before beginning work each day. Use the checklist on the next page as a guide for daily, visual inspections. Alert your supervisor if you find anything wrong during your daily pre-start inspection.
Belts
Check for loose or damaged belts. Loose belts can slip, causing friction and a possibly a fire. Belts can also break and be flung from the mower. Tighten loose belts and replace belts if any ply separation or cracks are visible.
Blade
Make sure the blade is secure, balanced and covered to prevent injury. Report bent, cracked or worn blades to your supervisor. Protect your hands with heavy-duty gloves when inspecting blades.
Fluid Leaks
Fluid leaks can be a fire hazard as well as cause break-downs. Report signs of leaking fluid to your supervisor immediately.
Accumulated Grass or Grease
Check the mower deck and chute for accumulations of grass clippings, leaves, grease and other debris. Debris build-up on moving parts is a fire hazard and can cause break-downs.
Missing or Damaged Guards
Guards and shields protect you from moving parts. Check the operator's manual for the location of guards and safety shields on the equipment you are using.
When Operating an Agricultural Mower
Ensure there is a shield covering the power take-off (PTO) to
keep you from being entangled in the rotating shaft. Also, if your
equipment has any belts or pulleys, make sure the guards are in
place and secured.
When Operating a Riding Mower
Ensure that the discharge chute's guard is in place to deflect debris and cover the mower's blade. Also, if your equipment has any belts or pulleys, make sure the guards are in place and secured. Also, check that the operator presence control is working properly. The control shuts the mower off automatically when weight is lifted off of the seat.
When Operating a Walk Behind Mower
Ensure the operator presence control is working properly. The engine should shut off automatically when the handle is released. There should be a rear guard installed to protect your feet, as well as a discharge chute on the side of the mower that deflects debris and covers the mower's blade.
|
|
Operator Presence Control |
|
Tires
Check tire pressure and look for signs of damage. Make sure lug
bolts are tight to keep the wheel from slipping off.
Attachments (if applicable)
Make sure attachments are mounted and fastened correctly.
String/Brush Trimmer
Ensure the shield covering the string/blade is in place and secured.
YES
Brush cutter with blade
guard in place.
|
NO
Brush cutter with no
blade guard.
|
|
|
Belts |
|
Secured? |
|
Not cracked or separated? |
|
|
Blade |
|
Secure and balanced? |
|
Sharpened? |
|
Free of excessive wear? |
|
|
Fluid Leaks |
|
No sign of fluid leaks? |
|
|
Accumulated Grass or Grease |
|
Mower, deck and chute free of debris? |
|
|
Guards |
|
All guards in place? |
|
No sign of damaged guards? |
|
|
Tires |
|
Proper inflation? |
|
No visible damage? |
|
Lug bolts tight? |
|
|
Attachments (if applicable) |
|
Mounted and secured properly? |
|
|
String/Brush Trimmer |
|
String/blade attached properly? |
|
String/blade shield in place and secured? |
Prepare the mowing area before beginning to ensure a safe working environment for yourself and others.
Remove Debris
Walk the area to be mowed. Pick up debris such as rocks, sticks, bottles, cans, wires, etc. Debris picked up by a mower or trimmer can be thrown from the machine at speeds as high as 200 mph or cause the equipment to jam or malfunction.
Be Aware of Surroundings
While scanning the area for debris, locate other potential hazards such as ditches, drop-offs or embankments.
Be aware at all times of the location of coworkers. Keep all others out of the area while you are mowing or trimming.
Make sure that the chute of the mower is pointed away from people, animals, buildings and traffic.
Accident Report
Operator Struck in Eye by Rock |
Summary of OSHA Accident Inspection 119964930
An employee was operating a string trimmer near a coworker. The trimmer caught a rock and threw it at the coworker, striking him in the eye. The coworker was hospitalized for two days.
Always be aware of the location of coworkers and wear appropriate eye protection.
|
YES
No bystanders or coworkers
in the cutting area.
|
NO
Never mow or trim when
others are nearby.
|
YES
Mower chute pointed
away from obstructions.
|
NO
Never point chute near buildings,
people, animals or traffic.
|
- Make sure all attachments are disengaged.
- Shift into neutral before starting the engine.
* Always start string/brush trimmers on the ground.
* Start riding equipment from the operator's seat only.
* Keep hands and feet away from the blade area when starting walk behind mowers.
- Disengage the blade and other attachments.
- Lower the attachments to the ground.
- Shift the controls into neutral.
- Set the parking brake.
- Turn off the engine.
- Remove the key (if applicable).
Accident Report
Employee Crushed When Run over by Tractor |
Summary of OSHA Accident Inspection 123560880
An employee, jump-starting his tractor mower with another battery, connected the cables. The tractor was in gear, started and ran over the employee, crushing him to death.
Always shift the gear to neutral before shutting down equipment. Refer to the operator's manual for jump-starting instructions.
|
Gasoline and other fuels are flammable. Follow safe fueling procedures to help reduce the risk of fuel ignition.
- Always shut off the engine and wait at least 5 minutes for the engine to cool before refueling.
- Use only approved fuel containers and store in a well-ventilated area, away from direct sunlight.
- Never smoke or have an open flame near fuel
- Touch the fuel nozzle to the machine before removing the fuel cap to prevent a static spark from igniting the fuel.
- Use a funnel or a non-spill nozzle when fueling to reduce spillage.
- Keep the nozzle or funnel in contact with the fuel tank while filling.
- Wipe up all spills immediately, before starting the engine.
- Never clean your hands with gasoline. Use a nonflammable solvent instead.
Accident Report
Employee Burned When Gas Ignites |
Summary of OSHA Accident Inspection 002841710
The operator of a riding mower attempted to refuel the mower he had been using. As he was filling the gas tank, some gasoline ignited as it spilled onto the hot motor. The employee suffered first degree burns to his face and forearms.
Always shut off engine and wait at least 5 minutes for it to cool before fueling.
|
- Set the container on the ground.
- Touch the nozzle to the container before removing the container lid.
- Keep the nozzle in contact with the container while filling.
- Don't fill to the brim. Leave room for expansion. Portable containers and gas tanks should be filled 3/4 full.
- To reduce the chance of static sparks, do not fill containers in the bed of a pickup or in a car.
Carbon monoxide (CO) is a colorless, odorless, tasteless gas that can poison and kill. Symptoms of CO poisoning include headache, nausea, weakness, dizziness, and the loss of consciousness. To avoid CO poisoning, operate all equipment outdoors. If you must work indoors, make sure there is adequate ventilation to prevent exposure to CO.
Accident Report
Employee Dies of CO Poisoning |
Summary of OSHA Accident Inspection 123812240
An employee was working on a lawn tractor with the engine running inside a garage. He was overcome by carbon monoxide and died.
Make sure there is adequate ventilation when equipment is run inside a building.
|
Choose the correct answer.
For answers, click here.
- Loose belts, fluid leaks and accumulated grass and grease can be ________ hazards.
a. Water
b. Wind
c. Fire
- Check the ________________ for the location of shields and guards on your equipment.
a. Operator's manual
b. Local newspaper
c. OSHA Web site
- Which illustration shows how to correctly mow beside buildings?
|
OR |
|
- To keep children and unauthorized people from starting the machine, always remove the _____ from riding equipment.
a. Lights
b. Key
c. Belts
- The gas tank should be filled after the engine has cooled for at least _______ minute(s).
a. 1
b. 3
c. 5
- Recognize safe operating procedures
to prevent a rollover
accident.
- Identify issues of concern when
mowing on slopes.
When a mower becomes unstable or out of balance, it can roll over. A human's reaction time is too slow to stop a rollover once it starts. Look over the area before you mow, noting all land elevation changes. Once you have assessed the area to be mowed, observe the following precautions to avoid rollover accidents.
Do not mow near drop-offs, ditches, embankments or steep slopes.
The wheels on your mower and attachments can drop off or slide over the edge, causing the mower to roll over. Use a string trimmer to cut grass in these locations.
Do not operate tractors and mowers on steep hills. Refer to the operator's manual for the maximum slope allowed for your equipment.
Accident Report
Employee Crushed When Tractor Overturned |
Summary of OSHA Accident Inspection 103039624
An employee started up a steep hill to mow around a storage building. The tractor overturned and rolled over the employee, crushing him to death.
Know the maximum slope on which your equipment can safely be operated.
|
Avoid sudden moves.
Abrupt starts, stops and sharp turns can make the equipment roll over.
Slow down when turning and make wide, gradual turns, especially when mowing on slopes.
Turning quickly and sharply can cause the mower to overturn. When mowing on slopes, don't turn unless you have to. If turning is required, turn slowly and downhill.
Mow up and down slopes, not across. Your mower can become unbalanced and overturn on slopes, if you do not drive in the correct direction. Mowing up and down slopes can help prevent a side rollover.
Keep the heavy end uphill to avoid a rollover. Refer to your operator's manual to determine which end is heavier.
YES
Mow up and down
slopes.
|
NO
Do not mow across
slopes.
|
Mow across slopes, not up and down, to keep you from sliding underneath the mower.
YES
Mow across slopes.
|
NO
Do not mow up and
down slopes.
|
Choose the correct answer.
For answers, click here.
- A __________________ should be used to cut grass in
areas where a mower cannot go such as ditches, drop-offs or
embankments.
a. Pair of scissors
b. String trimmer
c. Tractor with attachments
- When using an agricultural tractor or riding lawn mower on
slopes, which picture correctly illustrates the direction to
mow?
|
OR |
|
- When using a walk behind mower on slopes, which picture correctly illustrates the direction to mow?
|
OR |
|
- When turning, slow down and make wide, _________ turns.
a. Sharp
b. Gradual
c. Narrow
- Keep the ______ end of a riding mower or tractor uphill to help a avoid rear rollover.
a. Light
b. Heavy
c. Shiny
- Recognize safe operating procedures to avoid being caught in moving parts.
- Identify hazards associated with equipment parts.
Observe these precautions to prevent being caught in the equipment's moving parts.
- Keep both hands and feet on the equipment at all
times (if applicable). Never reach around or beneath a
running mower or trimmer.
YES
Mow across slopes. | NO
Do not mow up and down slopes.
|
- Never use a mower or trimmer without all shields and guards in place. Shields and guards protect you from being caught in moving parts and should always be in place and undamaged when operating mowers and trimmers.
Accident Report
Operator's Eye Cut by Flying Glass |
Summary of OSHA Accident Inspection 104395389
An employee was operating a walk behind mower in a ditch. The blade's rear guard was bent up at the bottom, leaving a 2-inch section exposed. The employee was backing the mower out of the ditch when he was struck in the right eye with a piece of glass. Never operate a mower or trimmer with a damaged guard. Always wear eye protection.
|
- Never add blades or chains not recommended by the manufacturer. A blade or chain not specifically designed for the equipment can seriously injure or kill you. Refer to the operator's manual for recommended attachments.
- Shut off the engine before picking up debris or unclogging the chute. If the mower becomes clogged, turn the engine off and disconnect the spark plug wire before attempting to clear debris from the discharge chute. String trimmers should also be turned off before removing debris.
Accident Report
Operator's Finger Amputated in Blade While Clearing Grass Clippings |
Summary of OSHA Accident Inspection 119960714
An employee tried to clear grass clippings from the discharge chute of a riding lawn mower. He reached in with his right hand while the mower was running and the blades engaged. The employee lost two of his fingers.
Shut off the mower and remove the spark plug wire before clearing debris from the chute.
|
Accident Report
Employee's Fingers Amputated While Clearing Debris from Beside Mower |
Summary of OSHA Accident Inspection 112004809
An employee was mowing grass when he reached down to pick up a piece of telephone wire from the ground beside the lawn mower. The blade caught the wire and pulled his left hand under the machine, amputating his index finger and the tip of his middle finger.
Shut off the mower and remove the spark plug wire before clearing debris from the chute.
|
YES
Turn off the engine and
disconnect the spark
plug wire before attempting
to clear debris from
mowing equipment.
|
NO
Do not reach in to unclog
while engine is running.
|
- Never work on the equipment while it is running. Turn off the engine, disconnect the spark plug wire (or unplug if electrical) and allow moving parts to stop before unclogging, adjusting, changing blades or working on equipment. This procedure should also be followed if you hit an object or if the equipment vibrates unusually.
Accident Report
Employee's Killed After Dismounting Running Tractor |
Summary of OSHA Accident Inspection 109574764
An employee was dismounting a tractor mower with the motor still running. He hit the shifter and the tractor went into forward gear. He was run over by the mower and killed.
Never dismount running equipment.
|
YES
Turn off the engine and
disconnect the spark
plug wire before adjusting
or working on mowing
equipment.
|
NO
Never work on running
equipment.
|
- Be cautious on wet grass. Slips on wet grass can cause you to fall into the equipment's moving parts. Also, wet grass can cause riding mowers and agricultural tractors to slide or skid, throwing you off.
Accident Report
Operator Cut by Mower Blade |
Summary of OSHA Accident Inspection 125582973
An employee was operating a riding mower without the blade guard in place. He dismounted the mower in order to move a picnic table in his path. The employee slipped on the wet grass and slid into the exposed rotating blade. He sustained a fractured right ankle, partial amputation of his left foot along with severe and extensive cuts.
Never operate a mower without all guards in place. Never dismount a running mower.
|
- Always push the mower, never pull, to keep from pulling the mower over your feet. Never lift the mower up. Push the mower forward to turn so that you do not pull the equipment over your feet.
Accident Report
Employee’s Toes Severed While Turning Mower |
Summary of OSHA Accident Inspection 119869220
An employee, operating a walk behind mower, encountered a wall. He lifted the front wheels in the air in order to turn. After turning, he put the front wheels back down, on top of his right foot. His five toes were severed when they entered the rotating blade area.
Never lift the mower up to complete a turn.
|
Choose the correct answer.
For answers, click here.
- When mowing, __________ grass can be a hazard to operators of all types of equipment.
a. Cut
b. Short
c. Wet
- Only blades recommended by the __________________ should be added to mowing equipment.
a. Manufacturer
b. Custodian
c. Operator
- Before performing maintenance or unclogging debris from the mower's chute, turn off the engine and __________________.
a. Let the air out of the tires
b. Disconnect the spark plug wire
c. Remove the steering wheel
- Identify steps to avoid being run over.
- Become aware of hitching and unhitching procedures.
- List precautions to avoid hitting obstacles.
- Recognize how to prevent objects from being thrown during equipment operation.
- Evaluate how to safely operate equipment in and around traffic.
- Become aware of electrical hazards.
You can be injured or killed if you are run over by mowing equipment. Protect yourself by following these steps to avoid runovers.
- Always start riding equipment from the operator's seat. Do not start riding equipment while standing beside it.
- Never carry extra passengers, including children, on a riding mower.
- Never leave running equipment unattended. Always follow proper shut-down procedures.
- Watch for traffic and pedestrians when crossing or working near roads, driveways, parking lots, building corners, shrubs, trees and other blind spots. People, animals and traffic move quickly and may not realize they are in the path of danger. Be aware of your surroundings at all times.
Use the following steps to avoid serious injury or death when hitching and unhitching attachments to an agricultural tractor.
- Hitch towed loads to the drawbar only.
- Never raise, lower or otherwise alter the drawbar. Hitching higher than the drawbar can cause a rear rollover.
- Refer to the operator's manual for instructions on hitching attachments with hydraulics, a 3-point hitch or PTO shaft.
- Ensure all safety guards are in place and undamaged. Unhitch attachments on level ground only.
- Keep others out of the area between the tractor and the attachment or implement.
You can be seriously injured or killed if you run into obstacles while mowing. Follow these precautions to avoid obstacles.
- Always be looking ahead for obstacles.
- Watch for trees, buildings, overhangs and other obstructions.
- Allow enough room to safely pass between obstructions. Be careful not to get too close.
- Check overhead clearance before passing beneath branches, awnings and other obstructions.
Accident Report
Operator Crushed When Wedged Between Tractor and
Tree Trunk |
Summary of OSHA Accident Inspection 106490485
An employee was backing a tractor mower between some trees. Unable to stop in time, the tractor became wedged under a partially fallen tree trunk. The employee was crushed against the tractor's steering wheel and killed.
Watch for obstacles when backing up.
|
Accident Report
Operator Killed When Run Over by Brush Hog |
Summary of OSHA Accident Inspection 112399985
An employee was operating a tractor with an attached brush hog at a speed of 6-8 mph. When he tried to pass between two trees, the right rear tire of the tractor struck one of the trees. The impact threw the employee off the tractor. He was run over by the brush hog and killed.
Allow plenty of room when passing between obstacles.
|
Accident Report
Operator Severs Fingers When Mower Slides on Wet Grass |
Summary of OSHA Accident Inspection 112046834
An employee was operating a riding mower on grass that was wet from rain the previous day. He was mowing near a tree on a slight incline, with his right hand resting on the gas tank. As he got closer to the tree, the mower slid and hit the tree in the same spot where he was touching the gas tank. Three of his fingers were severed. One was unable to be reattached.
Never mow on wet grass and always keep hands on the steering wheel of an agricultural tractor or riding mower.
|
Objects thrown from mowing equipment can cause severe injury. Follow these steps to protect yourself and others.
- Clear the work area before you begin. Pick up sticks, bottles, rocks, wires and other debris before you begin.
- Keep children and bystanders away from the area.
- Wear long pants to protect your legs from debris.
- Safety glasses should be worn at all times unless you are inside an enclosed cab.
- Safety glasses and a face shield should be worn when operating string and brush trimmers.
- Shut off equipment when crossing a sidewalk, driveway or road.
Check the operator's manual for instructions before hauling the mowing equipment on a trailer. Be sure to observe these precautions:
- Keep bystanders at a safe distance.
- Select a level surface.
- Block the rear wheels of the transport vehicle.
- Attach appropriate ramps to the transport vehicle.
- Back the mower up the ramp. Drive forward down the ramp.
- Chain and block the mowing equipment so it won't move during transport.
YES
Keep the heavy end of the mower
at the top of the ramp.
|
NO
Do not allow the heavy end of the mower
to be at the bottom of the ramp.
|
Accident Report
Employee Injured When Mower Overturned
on Tailgate |
Summary of OSHA Accident Inspection 125956334
An employee was driving a riding mower up a ramp to store it in a trailer. The hinge on the tailgate broke and the mower overturned. The employee was hospitalized with back injuries.
Ensure that any ramp used is securely attached to the loading vehicle.
|
Mowers are not made for street or highway travel. To be safe, load mowers and other equipment onto a trailer and pull them to the job site. When the mower must be moved short distances on a public roadway, keep the following safety tips in mind.
- Observe all traffic signals, signs and rules.
- Mount a Slow Moving Vehicle (SMV) emblem on the back to indicate the mower is moving at a speed less than 25 mph.
- Use caution at intersections. Allow fast moving vehicles to go first. Make sure you have enough time to get through safely, without interrupting traffic flow.
- Use a flagger and highly visible warning cones to alert oncoming traffic when working near a public roadway. Place flaggers and cones far enough ahead of the work site so drivers have time to slow down.
- The equipment operator and the flagger should wear highly visible, reflective clothing.
- Do not stand in the road to trim grass or brush. Stand away from the road and watch for traffic.
- Do not park the mower on a public roadway. It creates a hazard for you and motorists. Park away from the road on a level surface if the mower must be left at a job site.
Follow these precautions to keep you from being electrocuted while working with electric tools.
- Never cut off the ground pin (bottom prong) of a three-prong plug to fit in a two-prong outlet.
- Do not use electric equipment when grass is damp or wet.
- Keep ladders away from power lines.
- Use tools that are double insulated.
- Do not carry any tool by its cord.
- Ensure extension cords are in good condition and always use a cord labeled for outdoor use.
- Do not run over extension cords with equipment.
- Make sure electric tools are unplugged before working on, unclogging, or adjusting the equipment.
- Unplug all equipment immediately after use.
- When unplugging a tool or piece of equipment, do not yank the cord.
- Battery powered tools are much safer than electrical tools.
Using Ground-Fault Circuit Interrupters (GFCIs)
A GFCI is an electrical outlet that protects you from being electrocuted if an electrical tool or appliance malfunctions. The GFCI has a sensor and a microchip that can tell if electricity is going to the wrong place, such as through your body. When the GFCI senses a problem, it shuts off the electricity in about one-fortieth of a second, which is fast enough to save your life.
If a GFCI outlet is not available, a portable GFCI extension cord can be used.
Choose the correct answer.
For answers, click here.
- Riding equipment should always be started from __________.
a. Beside the mower
b. The operator's seat
c. Wherever's easiest
- When mowing, always be looking ____________.
a. At the sky
b. Ahead for obstacles
c. At my feet
- To move a mower to a site 3 miles away, it is better to _______.
a. Drive the mower there
b. Load it on a trailer and haul it there
c. Buy a new mower at the other site
- When loading a mower onto a trailer, ________ the rear wheels of the transport vehicle.
a. Take off
b. Spin
c. Block
- Do not use electric tools when the grass is ___________.
a. Freshly cut
b. Fertilized
c. Damp or wet
- Identify environmental hazards.
- Recognize treatment and first aid for exposure to environmental hazards.
Minor cuts and burns can be treated on-site with minimal complications. If you or a coworker sustains major cuts or burns, get professional medical help immediately.
Treating Minor Cuts
- Clean the area thoroughly.
- Remove any debris from the wound.
- Apply pressure to the wound using gauze or a clean, absorbent
cloth until the bleeding stops.
- Apply an antibiotic ointment and cover with a bandage or clean
gauze.
- Allow the wound to heal and keep dirt from creating infection
by changing the bandage or gauze frequently.
- Get medical help immediately if the cut is severe or if bleeding
does not stop in response to direct pressure.
Treating Minor Burns
- Cool the burn by placing it under cool running water or in a
container of cool water for at least 15 minutes. If the skin is
broken, do not place under water, instead, seek medical attention
immediately.
- Cover the area with gauze or a clean cloth.
- Allow the burn to heal and keep dirt from creating infection by
changing the gauze frequently.
- If blisters occur, do not break them. Cover with gauze and allow
to break on their own.
- Get medical help if the burn is serious or if burns cover large
areas of the body or occur on the face or genitals.
The following is a list of minimum requirements for workplace first aid kits as outlined by ANSI Standard Z308.1-2003*.
- absorbent compress
- adhesive bandages
- adhesive tape
- individual-use antiseptic applications
- individual-use burn treatment applications
- latex-free medical exam gloves
- sterile pads
- triangular bandage
*ANSI Z308.1-2003 is published by the International Safety Equipment Association, Arlington, VA www.safetyequipment.org. Used with permission.
You can become seriously ill or die if you do not take the proper precautions while working in high temperatures and humidity. Heat can reduce physical performance, as well as mental alertness, causing more accidents.
Heat illness starts at heat exhaustion, and if not treated properly, leads to heat stroke. Take action immediately if you notice anyone with the symptoms found in the charts below.
It is important to keep yourself hydrated and cool while working outside.
- Drink water often throughout the day; don't wait until you're thirsty to get a drink. At least a quart of water per hour is recommended.
- Stay away from soda, coffee, tea and alcoholic drinks that dehydrate the body.
- Avoid large meals before working in the heat.
- Some prescriptions can make you more susceptible to heat illnesses. Check with your doctor or pharmacist to see if any medicine you are taking could affect you while working in the heat.
- Wear light-weight fabric, such as cotton, to help keep your body cool.
- Plan to do the heaviest work at the coolest part of the day. This is usually between 6 a.m. and 10 a.m.
- Take frequent, short breaks in shaded areas to cool down.
- Do not take salt tablets, unless recommended by your doctor. Most people receive enough salt in their diet to account for the salt that is lost through sweating.
Heat Exhaustion Symptoms
Heat exhaustion is a serious illness and needs to be treated immediately before a heat stroke occurs. If you or a coworker experience any of the following symptoms, cool off immediately and drink plenty of water.
- Dizziness
- Light headedness
- Headache
- Feeling weak, fatigued
- Clammy and moist skin
|
Heat Stroke Symptoms
Heat Stroke is a medical emergency that can become fatal. If anyone experiences the following symptoms of heat stroke, call 911 immediately.
- Hot, dry, red skin (not sweaty)
- Disorientation
- Confusion
- Body temperature greater than 105° F
- Convulsing
- Unconsciousness
|
- If someone feels overheated, move them into a cooler, preferably air conditioned area. Watch the person and seek medical attention if needed.
- Fan the person in order to increase cooling.
- Have the person drink plenty of fluids.
- If the person goes into convulsions or shows symptoms of heat stroke, call 911 immediately and take steps to cool them down such as soaking their clothing in cool water.
Heat Facts
- You are more likely to suffer from a heat related illness on humid days.
- If you are not used to working in the heat, you are more likely to suffer from a heat related illness. It can take your body anywhere from 5 days to 2 weeks to be acclimated to working in the heat. It is recommended that new workers who begin in hot, humid weather, start out by working half of the normal time and workload on the first day and then build up to a complete day by the end of the week.
- You are more vulnerable to heat illness if you have suffered in the past.
- During the course of the day, you can produce as much as 2 to 3 gallons of sweat. Replenish this fluid by drinking liquids so that you do not suffer from a heat related illness.
Accident Report
Dehydrated Employee Dies After Working in Heat |
Summary of OSHA Accident Inspection 115237216
An employee was cutting lawns with a gas-powered mower in temperatures from 75° to 85° F. He had been working all day and told his employer that he felt tired. The employee was instructed to go rest in the company truck. When a coworker went to check on him, the employee was having convulsions. He was rushed to the hospital in an ambulance where his temperature was measured at 111° F. At the hospital, the employee had a seizure and died. The cause of death was reported as dehydration and heat stress.
Remember to keep yourself hydrated when working outside.
|
Prolonged exposure to sunlight causes skin cancer, cataracts and other serious illnesses.
- Choose a sunscreen that is marked broad-spectrum. This will protect you from both UVA and UVB rays. Ensure the Sun Protection Factor (SPF) is at least 15.
- Wear a hat or sun visor, sunglasses, and lightweight long-sleeve shirts and pants on sunny days to help control body temperature and block the sun.
Prolonged exposure to freezing temperatures can result in cold induced injuries and illnesses that can seriously injure or kill you.
Cold temperatures reduce mental alertness and cause fatigue and exhaustion that can lead to accidents.
Frostbite
Frostbite occurs when parts of the body become so cold that the skin and tissue freezes. Frostbite normally occurs on ears, nose, fingers, hands, toes and feet or other parts of the body that are left uncovered in below-freezing temperatures. Frostbitten skin becomes numb and turns a pale white color.
Hypothermia
Hypothermia occurs when a person's body temperature drops to or below 95° F. Common symptoms include bluish-colored skin, uncontrollable shivering and drowsiness or fatigue.
Avoid Cold-Induced Injuries and Illnesses
- Layer clothing when working in cold temperatures; you can easily take off layers if you are too warm.
- Wear a hat and gloves.
- Keep muscles warm and loose by moving as much as possible.
- Take frequent, short breaks in warm areas.
- Perform work at the warmest part of the day, typically in the afternoon.
- Never work alone.
What to Do If Someone's Suffering from a Cold-Induced Injury or Illness
- Move the person out of the cold and into an area that is warm and dry.
- Remove wet and tight clothing and cover the person with a blanket.
- Never rub the affected area. This will cause further skin and tissue damage.
- Seek medical attention immediately.
Insect stings can be treated without medical attention unless the person suffers an allergic reaction.
The first step to treating an insect sting is to remove the stinger. This can be done by using a straight edge to scrape off the stinger or by using tweezers to pull it out. If you choose to use tweezers to remove the stinger, use extreme caution to not puncture the protruding venom sac.
After the stinger has been removed, a cold pack can be used during the first 24 hours to suppress pain and swelling. Following the first 24 hours, heat should be applied if pain or swelling persist.
Those with severe allergies to insect stings should consult a physician about carrying a prescription medical kit. The kit contains medicine and instructions to be used if the person is stung. If the kit is used, the victim still must receive medical attention. Call for help or take them to the nearest hospital.
If you are bitten by a snake, seek medical attention immediately and try to describe the size and color of the snake to the doctor. This can help the doctor determine whether or not the snake was poisonous. Never cut, suck or apply cold packs to snake bites.
Never cut, suck or apply cold packs to snake bites.
Be aware of animals such as squirrels or bats that may be in trees or bushes and startle you during work. Also, be cautious of animals such as rats, skunks and raccoons that could be rabid.
- Wash the affected area and all clothing and tools that may have touched the plant.
- Avoid scratching the area if possible, to prevent infection.
- Hot and cold compresses can be used to suppress itching.
- Consult a doctor if the rash is on the face, inside the mouth or covers a large portion of the body.
|
Poison Ivy Leaves are usually found in clusters of three. |
Lightning strikes injure and kill hundreds of people each year. Follow these precautions to help keep you safe when the weather turns bad.
- As soon as you hear thunder, shut off and put away equipment and move indoors out of the storm. When you are able to hear thunder, you are able to be struck by lightning. Lightning can strike even when it's not raining.
- The cab of an enclosed vehicle provides some protection from lightning but a sturdy building provides the best protection.
- Listen to the radio for weather updates and storm warnings.
- Get to a low space. Lightning strikes the tallest objects.
- Crouch down on the balls of your feet. Place your hands on your knees and lower your head between your knees.
- Minimize contact with the ground.
- Do not lie flat on the ground. This will make you a larger target.
- Large, lone trees and towers, fences, telephone poles and power lines.
- Rivers, lakes, pools and other bodies of water.
- Metal objects, tools, equipment, wire fences and umbrellas.
- Call 911
- Check to see if they're breathing. Rescue breathing or CPR may be required.
- Check for burns on their body.
- Move the victim inside, out of the storm.
- Note: Most lightning-strike victims survive with immediate treatment and rescue breathing or CPR.
Accident Report
New Employee Killed When Struck by Lightning |
Summary of OSHA Accident Inspection 101558112
A new employee continued mowing when a light rain started. Lightning struck a nearby tree and killed the employee just two hours after he had started his new job.
If you see any signs of lightning or a thunderstorm, stop what you're doing and get inside.
|
Lightning Facts |
|
A person that is struck by lightning DOES NOT retain an electric charge that can shock you. |
|
Lightning can spread as far as 60 feet after striking the ground. |
|
Lightning can travel at speeds of 100,000 mph. |
|
The temperature of a bolt of lightning can be as high as 50,000° F. |
|
Lightning CAN strike the same place twice. |
Choose the correct answer.
For answers, click here.
- Stop a cut from bleeding by applying ______________.
a. Ice
b. Ointment
c. Direct pressure
- Dizziness, light headedness, headache and fatigue are all symptoms of _____________.
a. Sore thumb
b. Lightning strike
c. Heat exhaustion
- Is is important to take frequent, short _______ when working outside.
a. Phone calls
b. Breaks
c. Strides
- To keep hydrated when working outside, drink __________.
a. Water frequently throughout the day.
b. Only when thirsty.
c. Soda at lunchtime.
- Lightning strikes the _________ objects.
a. Tallest
b. Widest
c. Shortest
Select the correct answer for the following sentences from the list below.
- Immediately
- Stinger
- Wash
- Frostbitten
- Lower
- Never rub a body part that has been ___________.
- The first step to treating an insect sting is to remove the _____.
- If you contact poison ivy, oak or sumac, ______ the affected area as well as all clothing and tools.
- Hypothermia occurs when body temperature drops to 95° F or ___________.
- If a person with a known allergy to insects is stung, call for help ___________________.
Developing safe work habits before, during and after machinery
operation, helps you avoid accidents on the job.
You have been presented with checklists, safety tips and exercises
designed to help you avoid the most commonly reported causes of
mower and trimmer operation injuries and deaths, as well as other
important safety precautions to consider. Use this information to
keep your work experience safe.
Choose the correct answer.
For answers, click here.
- The two most commonly reported causes of serious injury and death involving mowing equipment are _________________.
a. Rollovers and being caught in moving parts
b. Carbon monoxide poisoning and lightning strikes
c. Cuts and burns
- A pre-start inspection should be performed __________.
a. Once each week
b. At the start of each work day
c. Whenever the weather is nice
- When operating a riding mower on a hill, mow _______ slopes.
a. Up and down
b. Across
- When operating a walk behind mower on a hill, mow _________ slopes.
a. Up and down
b. Across
- To avoid ______________, only add blades recommended by the manufacturer.
a. Running into obstacles
b. Spinning in circles
c. Being caught in moving parts
- Always _____________ obstacles and debris.
a. Trying to ignore
b. Look ahead for
c. Mowing over
- Riding mowers are NOT made for ________________.
a. Mowing grass
b. Highway travel
- Never carry an electric tool by its _________.
a. Cord
b. Handle
- Heat related illnesses are very ________ and should not be ignored.
a. Beneficial
b. Serious
c. Exciting
- If working indoors with running equipment, make sure there is adequate _________ to prevent carbon monoxide exposure.
a. Lighting
b. Fuel
c. Ventilation
Circle the correct answer.
- What are the two most commonly reported causes of serious injury and death from operating mowers and trimmers?
- Rollovers and being caught in moving parts.
- Heat stroke and lightning strike.
- Carbon monoxide poisoning and burns.
Select the correct answer for the following sentences from the list below.
a. Danger
b. Safety glasses
c. Alcohol
d. Caution
- The triangle shape is the symbol for d. Caution.
- b. Safety glasses should always be worn when operating mowing equipment.
- Never operate any type of equipment under the influence of c. Alcohol or drugs.
- a. Danger is the most serious safety message.
Choose the correct answer.
- When operating mowing equipment, it is important to wear clothes that are _________________.
- Expensive
- Close-fitting
- Ironed
- Wear _______ to protect your feet when mowing and trimming.
- Sandals
- Tennis shoes
- Sturdy boots
Choose the correct answer.
- Loose belts, fluid leaks and accumulated grass and grease can be ________ hazards.
a. Water
b. Wind
c. Fire
- Check the ________________ for the location of shields and guards on your equipment.
a. Operator's manual
b. Local newspaper
c. OSHA Web site
- Which illustration shows how to correctly mow beside buildings?
|
OR |
|
- To keep children and unauthorized people from starting the machine, always remove the _____ from
riding equipment.
a. Lights
b. Key
c. Belts
- The gas tank should be filled after the engine has cooled for at least _______ minute(s).
a. 1
b. 3
c. 5
Choose the correct answer.
- A __________________ should be used to cut grass in areas where a mower cannot go such as ditches, drop-offs or embankments.
a. Pair of scissors
b. String trimmer
c. Tractor with attachments
- When using an agricultural tractor or riding lawn mower on slopes, which picture correctly illustrates the direction to mow?
Up and Down |
OR |
Across |
- When using a walk behind mower on slopes, which picture correctly illustrates the direction to mow?
Up and Down |
OR |
Across
|
- When turning, slow down and make wide, _________ turns.
a. Sharp
b. Gradual
c. Narrow
- Keep the ______ end of a riding mower or tractor uphill to help a avoid rear rollover.
a. Light
b. Heavy
c. Shiny
Choose the correct answer.
- When mowing, __________ grass can be a hazard to operators of all types of equipment.
a. Cut
b. Short
c. Wet
- Only blades recommended by the __________________ should be added to mowing equipment.
a. Manufacturer
b. Custodian
c. Operator
- Before performing maintenance or unclogging debris from the mower's chute, turn off the engine and __________________.
a. Let the air out of the tires
b. Disconnect the spark plug wire
c. Remove the steering wheel
Choose the correct answer.
- Riding equipment should always be started from __________.
a. Beside the mower
b. The operator's seat
c. Wherever's easiest
- When mowing, always be looking ____________.
a. At the sky
b. Ahead for obstacles
c. At my feet
- To move a mower to a site 3 miles away, it is better to _______.
a. Drive the mower there
b. Load it on a trailer and haul it there
c. Buy a new mower at the other site
- When loading a mower onto a trailer, ________ the rear wheels of the transport vehicle.
a. Take off
b. Spin
c. Block
- Do not use electric tools when the grass is ___________.
a. Freshly cut
b. Fertilized
c. Damp or wet
Choose the correct answer.
- Stop a cut from bleeding by applying ______________.
a. Ice
b. Ointment
c. Direct pressure
- Dizziness, light headedness, headache and fatigue are all symptoms of _____________.
a. Sore thumb
b. Lightning strike
c. Heat exhaustion
- It is important to take frequent, short _______ when working outside.
a. Phone calls
b. Breaks
c. Strides
- To keep hydrated when working outside, drink __________.
a. Water frequently throughout the day.
b. Only when thirsty.
c. Soda at lunchtime.
- Lightning strikes the _________ objects.
a. Tallest
b. Widest
c. Shortest
Select the correct answer for the following sentences from the list below.
- Immediately
- Stinger
- Wash
- Frostbitten
- Lower
- Never rub a body part that has been d. Frostbitten.
- The first step to treating an insect sting is to remove the b. Stinger.
- If you contact poison ivy, oak or sumac,c. Wash the affected area as well as all clothing and tools.
- Hypothermia occurs when body temperature drops to 95° F or e. Lower.
- If a person with a known allergy to insects is stung, call for help a. Immediately.
Choose the correct answer.
- The two most commonly reported causes of serious injury and death involving mowing equipment are _________________.
a. Rollovers and being caught in moving parts
b. Carbon monoxide poisoning and lightning strikes
c. Cuts and burns
- A pre-start inspection should be performed __________.
a. Once each week
b. At the start of each work day
c. Whenever the weather is nice
- When operating a riding mower on a hill, mow _______ slopes.
a. Up and down
b. Across
- When operating a walk behind mower on a hill, mow _________ slopes.
a. Up and down
b. Across
- To avoid ______________, only add blades recommended by the manufacturer.
a. Running into obstacles
b. Spinning in circles
c. Being caught in moving parts
- Always _____________ obstacles and debris.
a. Trying to ignore
b. Look ahead for
c. Mowing over
- Riding mowers are NOT made for ________________.
a. Mowing grass
b. Highway travel
- Never carry an electric tool by its _________.
a. Cord
b. Handle
- Heat related illnesses are very ________ and should not be ignored.
a. Beneficial
b. Serious
c. Exciting
- If working indoors with running equipment, make sure there is adequate _________ to prevent carbon monoxide exposure.
a. Lighting
b. Fuel
c. Ventilation
MF2713
This material was produced under grant number 46G3-HT04 from the Occupational Safety and Health Administration, U.S. Department of Labor. It does not necessarily reflect the views or policies of the U.S. Department of Labor, nor does mention of trade names, commercial products, or organizations imply endorsement by the U.S. government.
This booklet was produced by K-State Research and Extension, Kansas State University, Manhattan, Kansas.
The information in this publication has been compiled from a variety of sources believed to be reliable and to represent the best current opinion on the subject. However, neither K-State Research and Extension nor its authors guarantee accuracy or completeness of any information contained in this publication, and neither K-State Research and Extension or its authors shall be responsible for any errors, omissions, or damages arising out of the use of this information. Additional safety measures may be required under particular circumstances.
Brand names appearing in this publication are for product identification purposes only. No endorsement is intended, nor is criticism implied of similar products not mentioned.
Disclaimer
and Reproduction Information: Information in NASD does not
represent NIOSH policy. Information included in NASD appears
by permission of the author and/or copyright holder. More
NASD Review: 05/2007
|