Click Here to Display Options
Click Here to Close Options
USACE / NAVFAC / AFCESA / NASA NASA-10800S (December 2005)
------------------------------------
Preparing Activity:
NASAMasterFormatTM 2004 - 10 28 13.00 40
Superseding
NASA-10800 (July 2002)
UFGS-10800 (July 2002)
UNIFIED FACILITIES GUIDE SPECIFICATIONS
References are NOT in agreement with UMRL
References will be in agreement at next scheduled update of UMRL
Section Table of Contents
SECTION 10800S
TOILET ACCESSORIES
12/05
PART 1 GENERAL
1.1 REFERENCES
1.2 SUBMITTALS
1.3 DELIVERY, STORAGE, AND HANDLING
1.4 WARRANTY
PART 2 PRODUCTS
2.1 MANUFACTURED UNITS
2.1.1 Anchors and Fasteners
2.1.2 Finishes
2.2 ACCESSORY ITEMS
2.2.1 Facial Tissue Dispenser (FTD)
2.2.2 Grab Bar (GB)
2.2.3 Medicine Cabinet (MC)
2.2.3.1 Sliding Door Cabinet, Class 1
2.2.3.2 Swinging Door Cabinet, Class 2
2.2.4 Mirrors, Glass (MG)
2.2.5 Mirror, Metal (MM)
2.2.6 Mirror, Tilt (MT)
2.2.7 Paper Towel Dispenser (PTD)
2.2.8 Combination Paper Towel Dispenser/Waste Receptacle Units (PTDWR)
2.2.9 Sanitary Napkin Disposer (SND)
2.2.10 Sanitary Napkin and Tampon Dispenser (SNTD)
2.2.11 Shower Curtain (SC)
2.2.12 Shower Curtain Rods (SCR)
2.2.13 Soap Dispenser (SD)
2.2.14 Soap Holder (SH)
2.2.15 Shelf, Metal, Heavy Duty (SMHD)
2.2.16 Shelf, Metal, Light Duty (SMLD)
2.2.17 Soap and Grab Bar Combination, Recessed (SGR)
2.2.18 Towel Bar (TB)
2.2.19 Towel Pin (TP)
2.2.20 Toilet Tissue Dispenser (TTD)
2.2.21 Toilet Tissue Dispenser, Jumbo (TTDJ)
2.2.22 Toothbrush and Tumbler Holder (TTH)
2.2.23 Waste Receptacle (WR)
2.2.24 Toilet Seat Cover Dispenser (TSCD)
2.2.25 Toilet Seat Cover/Tissue Dispenser/Waste Receptacle (TSCTDWR)
2.2.26 Electric Hand Dryer (EHD)
2.2.27 Diaper Changing Station (DCS)
PART 3 EXECUTION
3.1 INSTALLATION
3.1.1 Recessed Accessories
3.1.2 Surface Mounted Accessories
3.2 CLEANING
3.3 SCHEDULE
SECTION 10800S
TOILET ACCESSORIES
NOTE: This guide specification covers the requirements for
toilet accessories
suitable for a wide variety of applications.
Comments and suggestions on this guide specification are welcome and should
be directed to the technical proponent of the specification. A listing of
technical
proponents, including their organization designation and telephone number, is
on the Internet.
Recommended changes to a UFGS should be submitted as a
Criteria Change Request
(CCR).
Use of electronic communication is encouraged.
This guide specification includes tailoring options for paper towel dispenser,
combo towel dispenser/waste recept, and electric hand dryer. Selection or deselection
of a tailoring option will include or exclude that option in the section, but
editing the resulting section to fit the project is still required.
Brackets are used in the text to indicate designer choices or locations where
text must be supplied by the designer.
PART 1 GENERAL
NOTE: For Army construction, buildings not excluded by the TI 800-01 Design
Criteria will be accessible in accordance with 36 CFR, Part 1191, Americans
with Disabilities Act (ADA) Accessibility Guidelines for Buildings and Facilities.
Drawings will indicate location, dimensions, elevations, schedules, details,
and such other information as required to indicate the extent of the work.
Product selections shall be based on esthetic values and cost as related to
project needs.
1.1 REFERENCES
NOTE: This paragraph is used to list the publications cited in the text of
the guide specification. The publications are referred to in the text by basic
designation only and listed in this paragraph by organization, designation,
date, and title.
Use the Reference Wizard's Check Reference feature when you add a RID outside
of the Section's Reference Article to automatically place the reference in the
Reference Article. Also use the Reference Wizard's Check Reference feature
to update the issue dates.
References not used in the text will automatically be deleted from this section
of the project specification when you choose to reconcile references in the
publish print process.
The publications listed below form a part of this specification to the extent referenced. The publications are
referred to within the text by the basic designation only.
ASTM INTERNATIONAL (ASTM) |
|
ASTM C 1036 | | (2001) Standard Specification for Flat Glass |
1.2 SUBMITTALS
NOTE: Review Submittal Description (SD) definitions in Section 01330 SUBMITTAL
PROCEDURES and edit the following list to reflect only the submittals required
for the project. Submittals should be kept to the minimum required for adequate
quality control.
A “G” following a submittal item indicates that the submittal requires Government
approval. Some submittals are already marked with a “G”. Only delete an existing
“G” if the submittal item is not complex and can be reviewed through the Contractor’s
Quality Control system. Only add a “G” if the submittal is sufficiently important
or complex in context of the project.
For submittals requiring Government approval on Army projects, a code of up
to three characters within the submittal tags may be used following the "G"
designation to indicate the approving authority. Codes for Army projects using
the Resident Management System (RMS) are: "AE" for Architect-Engineer; "DO"
for District Office (Engineering Division or other organization in the District
Office); "AO" for Area Office; "RO" for Resident Office; and "PO" for Project
Office. Codes following the "G" typically are not used for Navy, Air Force,
and NASA projects.
Choose the first bracketed item for Navy, Air Force and NASA projects, or choose
the second bracketed item for Army projects.
Government approval is required for submittals with a "G" designation; submittals not having a "G" designation
are [for Contractor Quality Control approval.][for information only. When used, a designation following the
"G" designation identifies the office that will review the submittal for the Government.] Submit the following
in accordance with Section
01330
01330
01330 SUBMITTAL PROCEDURES:
SD-03 Product Data
Finishes[; G][; G, [_____]]
Accessory Items[; G][; G, [_____]]
Manufacturer's descriptive data and catalog cuts indicating materials of construction, fasteners
proposed for use for each type of wall construction, mounting instructions, operation instructions,
and cleaning instructions.
SD-04 Samples
Finishes[; G][; G, [_____]]
Accessory Items[; G][; G, [_____]]
One sample of each accessory proposed for use. Incorporate approved samples into the finished
work, providing they are identified and their locations noted.
SD-07 Certificates
Accessory Items
Submit for each type of accessory specified, attesting that the items meet the specified requirements.
SD-10 Operation and Maintenance Data
Electric Hand Dryer[; G][; G, [_____]]
[Four] [_____] complete copies of maintenance instructions listing routine maintenance procedures
and possible breakdowns. Include repairs instructions for simplified wiring and control diagrams
and other information necessary for unit maintenance.
1.3 DELIVERY, STORAGE, AND HANDLING
Wrap toilet accessories for shipment and storage, then delivered to the jobsite in manufacturer's original packaging,
and stored in a clean, dry area protected from construction damage and vandalism.
1.4 WARRANTY
Warrant or guarantee all manufacturer's standard performance that extend beyond a 1 year period.
PART 2 PRODUCTS
NOTE: Only those accessories and finishes normally suitable for military construction
are included in this guide specification. When other accessories and finishes
are required to meet the needs of the project, the specifier must add them.
Maximum use should be made of recessed accessories in areas of hard usage.
2.1 MANUFACTURED UNITS
Provide toilet accessories in accordance with paragraph SCHEDULE. Porcelain type, tile-wall accessories are
specified in Section
09310S
09310S
09310S CERAMIC TILE. Provide each accessory item with the necessary mounting plates of
sturdy construction with corrosion resistant surface.
2.1.1 Anchors and Fasteners
NOTE: Tamperproof fasteners will be specified for accessories which have exposed
fasteners in areas used by neuropsychiatric patients or prisoners and where
theft or vandalism would be a problem. This guide specification places the
responsibility with the Contractor for providing, subject to Government approval,
fasteners and anchors of the type, size and number required to adequately secure
the accessory items. Specific requirements for critical or unusual applications
may refer to details on the drawings, or the specifications may be expanded
to include the necessary requirements.
Provide anchors and fasteners capable of developing a restraining force commensurate with the strength of the
accessory to be mounted and suited for use with the supporting construction. Provide [tamper proof design] [oval
head] exposed fasteners with finish to match the accessory.
2.1.2 Finishes
Except where noted otherwise, provide the following finishes on metal:
Metal Finish
Stainless steel No. 4 satin finish
Carbon steel, copper alloy, Chromium plated, bright
and brass
2.2 ACCESSORY ITEMS
NOTE: Drawings will show location, widths and heights, and vertical height
above finished floor, as required, for accessory items.
Only those accessory items to be used will be retained. Identifying abbreviation
in parentheses will be retained for those items to be used and shown on the
drawings. The various accessory items will generally be used in the following
locations:
DCS: Public toilets and toilets in nondomiciliary type buildings in accordance
with the requirements of the using service.
EHD: Public toilets and toilets in nondomiciliary type buildings upon specific
written request by the using service.
FTD: Private bathrooms used by women. Private/semi-private bathrooms in guest/transient
quarters. Limit to one per bathroom.
GB: Bathrooms that will be used by handicapped or people in a weakened condition,
such as in hospitals. Vertical grab bars should be considered in private bathrooms
where a soap and grab bar combination (SGR) accessory is not provided. Forms
and lengths will be shown on the drawings.
MC: Private bathrooms where storage of personal items in the bathroom is desirable.
Limit to one per bathroom.
MG: Private bathrooms where a medicine cabinet is not provided, in general-use
toilets, and hand washing areas. Mirror 450 mm 18 inches by 750 mm 30 inches
will be specified in Section 08805S GLASS AND GLAZING. Limit to not more than
one per lavatory. Adjustable tilt mirror will be provided in areas to be used
by wheelchair handicapped.
MM: Areas used by neuropsychiatric patients or prisoners and where vandalism
would be a problem. Limit to one per toilet in single lavatory installation.
PTD: Public toilets and toilets in nondomiciliary type buildings in accordance
with the requirements of the using service. Limit to not more than one per
two lavatories, except one per toilet in single lavatory installation.
PTDWR: Public toilets and toilets in nondomiciliary type buildings in areas
which have regularly scheduled waste removal. Limit to one per two lavatories
except one per toilet in single lavatory installation.
SND: Public toilets and toilets in nondomiciliary type buildings used by women.
Disposer will be mounted in the toilet compartments. Each toilet compartment
shall be accessible to a disposal unit.
SNTD: Public toilets and toilets in nondomiciliary type buildings used by women.
Use of recessed units will be considered for installations which are required
to present an excellent appearance. Limit to one per toilet.
SC & SCR: Installations with combination bathtub and shower SCR units which
include rails and curtains. One per shower-tub installation and one per individual
shower installation.
SD: Public toilets and toilets in nondomiciliary type buildings unless included
with paper towel dispenser. Limit to one per lavatory.
SH: Private toilets with lavatory unless soap dispenser is specified. Limit
to one per private toilet.
SMHD: Troop facilities and other areas subject to rough usage. Installation
will be detailed on the drawings.
SMLD: Private bathrooms where a glass shelf or medicine cabinet is not provided.
SGR: Installations with bathtub or shower. Limit to one per bathtub or shower-tub
installation and one per separate showerhead.
TB: Private bathrooms. Limit to two per bathroom. For safety purposes in
wet areas consider using a horizontal grab bar in lieu of towel bar.
TSCD: Public toilets and toilets in nondomiciliary type buildings in accordance
with the requirements of the using service.
TP: Private bathrooms where a shower is provided in lieu of a bathtub. Limit
to one per bathroom.
TTD: All toilet areas. Limit to one per water closet.
TTH: Private bathrooms. Limit to one per lavatory.
WR: Public toilets and toilets in nondomiciliary type buildings when requested
by the using service. Limit to not more than one per two paper towel dispensers.
Use of recessed combination units will be considered for installations which
have frequent scheduled trash removal service.
Conform to the requirements for accessory items specified below.
2.2.1 Facial Tissue Dispenser (FTD)
Provide [surface] [recessed] mounted facial tissue dispenser, Type 304 stainless steel face, [satin finish] [bright
polished finish]. Secure face of recessed dispenser by friction with suitable spring steel clips. Providea
minimum capacity of [150] [200] [300] two-ply tissues for dispenser.
2.2.2 Grab Bar (GB)
Provide an 18 gauge, 32 mm1-1/4 inch grab bar OD Type 304 stainless steel. Provide form and length for grab
bar as indicated. Provide [concealed] [exposed] mounting flange. Provide grab bar with [satin finish] [peened
non-slip surface]. Furnish installed bars capable of withstanding a 2.225 kN500 pound vertical load without
coming loose from the fastenings and without obvious permanent deformation. Allow 38 mm 1-1/2 inch space between
wall and grab bar.
2.2.3 Medicine Cabinet (MC)
Construct medicine cabinet with cold-rolled carbon steel sheet of minimum thickness 0.76 mm .03 inch, formed
from a single sheet of steel or mechanically formed spot welded. Provide width, height and depth of cabinet
in accordance with paragraph SCHEDULE.
2.2.3.1 Sliding Door Cabinet, Class 1
Provide [surface mounted vanity] [recessed cabinet] sliding door cabinet assembly with design and lighting arrangement
as indicated. Provide a minimum of 2 shelves per cabinet. Provide [a wide frame] [a narrow frame] [no frame]
mirror.
2.2.3.2 Swinging Door Cabinet, Class 2
Indicate swinging door cabinet assembly including the lighting arrangement.Provide [surface] [recess] mounted
assembly. Locate cabinet centrally behind the door with a minimum of two shelves. Provide stainless steel or
carbon steel door hinges. Provide permanent type magnets used in door catches. Provide doors [with] [without]
a mirror.
2.2.4 Mirrors, Glass (MG)
Provide Type I transparent flat type, Class 1-clear glass for mirrors. Glazing Quality q1 6 mm1/4 inch thick
conforming to ASTM C 1036. Coat glass on one surface with silver coating, copper protective coating, and mirror
backing paint. Provide highly adhesive pure silver coating of a thickness which provides reflectivity of 83
percent or more of incident light when viewed through 6 mm1/4 inch thick glass, free of pinholes or other defects.
Provide copper protective coating with pure bright reflective copper, homogeneous without sludge, pinholes or
other defects, of proper thickness to prevent "adhesion pull" by mirror backing paint. Provide mirror backing
paint with two coats of special scratch and abrasion-resistant paint and baked in uniform thickness to provide
a protection for silver and copper coatings which will permit normal cutting and edge fabrication.
2.2.5 Mirror, Metal (MM)
Provide a brightly polished stainless steel, metal mirror of, 0.94 mm 0.037 inch minimum thickness, edges turned
back 6 mm1/4 inch and recess fitted with tempered hardboard backing, and theft-proof fasteners. Provide size
in accordance with paragraph SCHEDULE.
2.2.6 Mirror, Tilt (MT)
NOTE: Mounting height of mirror shall be shown on the drawings.
Provide surface mounted tilt mirror with full visibility for persons in a wheelchair. Furnish [adjustable] [fixed]
tilt mirror, extending at least 100 mm4 inch from the wall at the top and tapering to 25 mm1 inch at the bottom.
Provide size in accordance with [paragraph SCHEDULE] [the drawings] [_____]. Conform to ASTM C 1036 and paragraph
for Glass Mirrors.
2.2.7 Paper Towel Dispenser (PTD)
NOTE: A tumbler key lock is the standard locking mechanism for manufacturers
and push button or twist-type locks are normally a specialty, extra-cost item,
if available.
Provide [_____] paper towel dispenser constructed of a minimum [22 gauge carbon steel] [0.683 mm0.269 inch Type
304 stainless steel], [surface] [recessed] mounted. Provide a towel compartment and a [mirror door] [and] [liquid
soap dispenser] for each dispenser. Furnish [tumbler key lock] [concealed tumbler key lock] locking mechanism.
2.2.8 Combination Paper Towel Dispenser/Waste Receptacle Units (PTDWR)
Provide [recessed] [semi-recessed] dispenser/receptacle with a capacity of [400] [600] [_____] sheets of C-fold,
single-fold, or quarter-fold towel. Design waste receptacle to be locked in unit and removable for service.
Provide tumbler key locking mechanism. Provide waste receptacle capacity of [45] [68] [_____] L.[12] [18] [_____]
gallons. Fabricate a minimum 0.8 mm 0.30 inch stainless steel welded construction unit with all exposed surfaces
having a satin finish. Provide waste receptacle that accepts reusable liner standard for unit manufacturer.
2.2.9 Sanitary Napkin Disposer (SND)
Construct a Type 304 stainless steel sanitary napkin disposal with removable leak-proof receptacle for disposable
liners. Provide [fifty] [_____] disposable liners of the type standard with the manufacturer. Retain receptacle
in cabinet by tumbler lock. Provide disposer with a door for inserting disposed napkins, [recessed] [partition
mounted, double access] [surface mounted].
2.2.10 Sanitary Napkin and Tampon Dispenser (SNTD)
NOTE: Specify sanitary napkin and tampon dispensers only when they are specifically
requested, in writing, by the Using Agency.
Provide sanitary napkin and tampon dispenser [surface mounted] [recessed]. Dispenser, including door of Type
304 stainless steel that dispense both napkins and tampons with a minimum capacity of 20 each. Furnish dispensing
mechanism for [complimentary] [coin] operation. Provide coin mechanisms with minimum denominations of 10 cents,
25 cents, 50 cents, [_____] [free]. Hang doors with a full-length corrosion-resistant steel piano hinge and secure
with a tumbler lock. Provide keys for coin box different from the door keys.
2.2.11 Shower Curtain (SC)
Provide [_____] shower curtain, size to suit conditions. Provide anti-bacterial nylon/vinyl fabric curtain.
Furnish [_____] color [as shown in Section
09915
09915
09915 COLOR SCHEDULE].
2.2.12 Shower Curtain Rods (SCR)
Provide Type 304 stainless steel shower curtain rods 32 mm 1-1/4 inch OD by 1.24 mm0.049 inch minimum [straight]
[bent as required] to meet installation conditions.
2.2.13 Soap Dispenser (SD)
NOTE: Powdered soap dispenser should be included for a shop or industrial area.
Edit to meet project requirements.
Provide [surface mounted soap dispenser, liquid type consisting of a vertical Type 304 stainless steel tank with
holding capacity of 1.2 L40 fluid ounces with a corrosion-resistant all-purpose valve that dispenses liquid
soaps, lotions, detergents and antiseptic soaps.] Provide [surface mount, powder type constructed of stainless
steel or chromium plated zinc die casting, containing a swap feed mechanism and an agitator designed to break
up powdered soap, with a minimum capacity of 0.94 L.32 ounces.] [lavatory mounted, liquid type consisting of
a polyethylene tank with a minimum 0.94 L32 fluid ouncesholding capacity and a [100 mm4 inch] [150 mm6 inch
] spout length.]
2.2.14 Soap Holder (SH)
Provide [surface mounted] [recessed] Type 304 stainless steel soap holder. Provide stainless steel separate
supports.
2.2.15 Shelf, Metal, Heavy Duty (SMHD)
NOTE: Where rough usage is anticipated, shelf support brackets and through-bolting
of accessories should be required and indicated on the project drawings.
Furnish a minimum 18 gauge stainless steel heavy duty metal shelf with hemmed edges. Provide shelves over 750
mm 30 inch with intermediate supports. Provide minimum of 16 gauge supports, welded to the shelf, and spaced
no more than 750 mm 30 inch apart.
2.2.16 Shelf, Metal, Light Duty (SMLD)
Support light duty metal shelf between brackets or on brackets. Purpose of brackets is to prevent lateral movement
of the shelf. Furnish [450 mm 18 inch][ 600 mm 24 inch] long shelf. Provide stainless steel shelf and brackets.
2.2.17 Soap and Grab Bar Combination, Recessed (SGR)
Provide recessed type, Type 304 stainless steel soap and grab bar combination, [bright polished finish] [satin
finish].
2.2.18 Towel Bar (TB)
Provide stainless steel towel bar with a minimum thickness of 0.38 mm. 015 inch. Provide minimum 19 mm3/4 inch
diameter bar, or 16 mm 5/8 inch square. Provide [bright polish] [satin] finish.
2.2.19 Towel Pin (TP)
Provide towel pin with concealed wall fastenings, and a pin integral with or permanently fastened to wall flange
with maximum projection 100 mm 4 inch. Provide [bright polish] [satin] finish.
2.2.20 Toilet Tissue Dispenser (TTD)
Furnish [Type II - surface mounted] [Type III - recess mounted] toilet tissue holder with two rolls of standard
tissue [mounted horizontally] [stacked vertically]. Provide [carbon steel, bright chromium plated finish] [stainless
steel, satin finish] cabinet.
2.2.21 Toilet Tissue Dispenser, Jumbo (TTDJ)
Provide surface mounted toilet tissue dispenser with 2 rolls of jumbo tissue. Fabricate cabinet of [Type 304,
18 gauge stainless steel with Type 304, 20 gauge stainless steel door] [high-impact plastic body and transparent
plastic front cover]. Provide cover with key locks.
2.2.22 Toothbrush and Tumbler Holder (TTH)
Provide stainless steel, surface mounted toothbrush and tumbler holder. Furnish holder to hold a minimum of
four toothbrushes in a vertical position. Provide 57 plus or minus 3 mm 2-1/4 plus or minus 1/8 inch in diameter
size of hole for securing tumbler.
2.2.23 Waste Receptacle (WR)
NOTE: Locks are typically provided on recessed and semi-recessed receptacles.
Provide Type 304 stainless steel waste receptacle, designed for [recessed] [surface] mounting. Provide reuseable
liner, of the type standard with the receptacle manufacturer. Provide a minimum [_____] cubic meter cubic feet
capacity. Provide receptacles with push doors and doors for access to the waste compartment with continuous
hinges. Furnish [tumbler key lock] [_____] locking mechanism.
2.2.24 Toilet Seat Cover Dispenser (TSCD)
Provide Type 304 stainless steel with [recessed mounted] [surface mounted] toilet seat cover dispensers. Provide
dispenser with a minimum capacity of 500 seat covers.
2.2.25 Toilet Seat Cover/Tissue Dispenser/Waste Receptacle (TSCTDWR)
Provide stainless steel and [partition mounted] [recessed mounted] [surface mounted] toilet seat cover, tissue
dispenser, and waste receptacle combination. Provide a minimum of 500 [seat covers] [seat covers per side] and
[2] [4 (2 per side)] standard tissue rolls for each dispenser. Provide a waste receptacle of the reuseable liner
of type standard with the receptacle manufacturer. Provide receptacle with [_____] cubic meter cubic feet capacity.
Furnish [tumbler key lock] [_____] locking mechanism.
2.2.26 Electric Hand Dryer (EHD)
NOTE: Consider the use of electric hand driers in public toilet areas that
may not receive daily custodian care and in areas where cleanliness is an issue
such as food preparation, dining facilities, and hospitals.
Provide wall mount and electric hand dryer designed to operate at 110/125 volts, 60 cycle, single phase alternating
current with a heating element core rating of a maximum 2100 watts. Provide dryer housing of single piece construction
and of [white porcelain enamel] [chrome plated steel] [baked electrostatically applied epoxy] [_____].
2.2.27 Diaper Changing Station (DCS)
NOTE: Omit requirement for integral dispenser for sanitary liners if not required.
Provide [recess mount] [surface mount] diaper changing station and fabricateof high impact plastic with no sharp
edges. Concave unit fold down platform to the child's shape, equipped with nylon and velcro safety straps engineered
to withstand a minimum static load of [
155 kg 340 lb] [
113 kg 250 lb]. Provide an integral dispenser for sanitary
liners for each unit. Provide pictorial for universal use of safety graphics. Provide [_____] color [as shown
in Section
09915
09915
09915 COLOR SCHEDULE].
PART 3 EXECUTION
3.1 INSTALLATION
Provide the same finish for the surfaces of fastening devices exposed after installation as the attached accessory.
Provide oval exposed screw heads. Install accessories at the location and height indicated. Protect exposed
surfaces of accessories with strippable plastic or by other means until the installation is accepted. After
acceptance of accessories, remove and dispose of strippable plastic protection. Coordinate accessory manufacturer's
mounting details with other trades as their work progresses. Use sealants for [brackets, plates, anchoring devices
and similar items in showers [a silicone or polysulphide sealant] as they are set to provide a watertight installation.]
After installation, thoroughly clean exposed surfaces and restore damaged work to its original condition or replace
with new work.
3.1.1 Recessed Accessories
Fasten accessories with wood screws to studs, blocking or rough frame in wood construction. Set anchors in mortar
in masonry construction. Fasten to metal studs or framing with sheet metal screws in metal construction.
3.1.2 Surface Mounted Accessories
NOTE: Shelf support brackets and through-bolting of accessories should be required
and indicated on the project drawings when rough usage of accessories is anticipated.
Attachment by through-bolting should be indicated for shelf brackets and mirrors.
Mount on concealed backplates, unless specified otherwise. Conceal fasteners on accessories without backplates.
Install accessories with sheet metal screws or wood screws in lead-lined braided jute, teflon or neoprene sleeves,
or lead expansion shields, or with toggle bolts or other approved fasteners as required by the construction.
Install backplates in the same manner, or provide with lugs or anchors set in mortar, as required by the construction.
Fasten accessories mounted on gypsum board and plaster walls without solid backing into the metal or wood studs
or to solid wood blocking secured between wood studs, or to metal backplates secured to metal studs.
3.2 CLEANING
Clean material in accordance with manufacturer's recommendations. Do not use alkaline or abrasive agents. Take
precautions to avoid scratching or marring exposed surfaces.
3.3 SCHEDULE
NOTE: A schedule of the accessories required will be added. Format for the
schedule may be modified to suit local preference. In some cases it may be
adequate to simply show the locations on the drawings or to specify locations
in the specification text.
Accessories Required
Room
or
Space MG PTD SMLD SD SH TTD
_____ ______________________________________________
[_____] [_____] [_____] [_____] [_____] [_____] [_____]
-- End of Section --