; This file contains the GOLF CRUISE PHASE TIME-LINE. ; Time-line has the requested format: TIME # ACTION # COMMENT ; Time has the format: dd & hh:mm ; The purpose of this is to make the file machine readable for input to ; the SOHO timeline IDL program ; Blank lines and comment lines --preceeded by ";" -- are ignored 0 & 06:00 # Run GOLF Main Channel GLF_ON CF # Check door is closed 0 & 06:30 # Run Main Channel GLF_OFF # 4 & 00:30 # Run Main Channel GLF_ON # Initiate Main Ch. Commissioning 4 & 01:00 # Run Main GLF_COM and GLF_COM_D # Including motors tests 4 & 03:30 # Run Main GLF_RECOVERY # Returning to Stand by mode 4 & 04:00 # Send GBMMON # Activating Magnetic modulation 4 & 04:01 # Send GBCBCST + parameter # Initiating Bulb heating 4 & 06:00 # Send GBCSCST + parameter # Initiating Stem heating 8 & 00:00 # Run Main Channel GLF_OFF # Before switching to Red 8 & 00:30 # Run Red Channel GLF_ON # Initiating Red Ch. Commissioning 8 & 01:00 # Run Red Channel GLF_COM and GLF_COM_D # Including motors test 8 & 03:30 # Run Red GLF_RECOVERY # 8 & 04:00 # Send GBMMON # Activating modulation 8 & 04:01 # Send GBCBCST + parameter # Initiating cell Bulb heating 8 & 06:00 # Send GBCSCST + parameter # heating Stem 12 & 00:00 # Run Red Channel GLF_OFF CF # Optional : if Main is to be run 12 & 00:30 # Run Main Ch. GLF_ON # Optional if Main is selected for next test 12 & 01:01 # Send GBMMON # 12 & 01:02 # Send GBPOINI + parameter # Select Polariser initial angle 12 & 01:03 # Send GBQWINI + parameter # Select Quarter-Wave initial angle 12 & 01:04 # Send GBPONOM # Initiating mechanisms nominal actuation 12 & 01:05 # Send GBDOOP # Opening Door for stray light measurement 12 & 01:15 # Send GBCBCST + parameter # Initiating Cell Bulb heating 13 & 00:00 # Send GBCSCST + parameter # Initiating Stem heating 13 & 01:00 # Send GBCBCST + parameter # Adjust Bulb heating 13 & 01:01 # Send GBCSCST + parameter # Adjust Stem heating 13 & 02:00 # Send GBCBCST + param # Adjust Bulb heating 13 & 02:01 # Send GBCSCST + param # Adjust Stem Heating 13 & 02:02 # Send GBFICST + param # Adjust Filter heating 14 & 00:00 # Send GBCSCST + param # Calibrate measured velocity/cell temp. 14 & 01:00 # Send GBCSCST + param # 14 & 02:00 # Send GBCSCST + param # 14 & 03:00 # Send GBCSCST + param # 14 & 04:00 # Send GBCSCST + param # 14 & 05:00 # Send GBCSCST + param # 14 & 06:00 # Send GBCSCST + param # 14 & 07:00 # Send GBCSCST + param # 14 & 08:00 # Send GBCSCST + param # 15 & 00:00 # Send GBCSCST + param # 15 & 01:00 # Send GBCSCST + param # 15 & 02:00 # Send GBCSCST + param # 15 & 03:00 # Send GBCSCST + param # 15 & 04:00 # Send GBCSCST + param # 15 & 05:00 # Send GBCSCST + param # 15 & 06:00 # Send GBCSCST + param # 15 & 07:00 # Send GBCSCST + param # 15 & 08:00 # Send GBCSCST + param # 16 & 00:00 # Send GBCSCST + param # 16 & 01:00 # Send GBCSCST + param # 16 & 02:00 # Send GBCSCST + param # 16 & 03:00 # Send GBCSCST + param # 16 & 04:00 # Send GBCSCST + param # 16 & 05:00 # Send GBCSCST + param # 16 & 06:00 # Send GBCSCST + param # 16 & 07:00 # Send GBCSCST + param # 16 & 07:00 # Send GBCSCST + param # 18 & 00:00 # VIRGO 10 arcmin in E-W and N-S direction depointing calibration # GOLF coordinated obs. 19 & 06:00 # Send GBDOCL # Close door prior to Mid Course Correction MCC2 23 & 00:00 # Send GBDOOP # Open door after MCC2 24 & 00:00 # Start Oscillating S/C around Yb axe # Cal suscept./pointing 24 & 10:00 # Stop oscillating S/C # 25 & 00:00 # Start oscillating S/C around Zb # 25 & 10:00 # Stop oscillating S/C # 26 & 00:00 # Start oscillating S/C around Xb # 26 & 10:00 # Stop oscillating S/C # 75 & 00:00 # Send GBDOCL # Close door before wheels momentum dump 76 & 12:00 # Send GBDOOP # Open door after wheels unloading 100 & 00:00 # Roll S/C 90 degrees around pointing axis # Init. pointing cal 100 & 00:10 # Start oscillating S/C around Yb # Cal GOLF and SUMER suscept. 100 & 10:00 # Stop oscillating S/C # 101 & 00:00 # Start oscillating S/C Around Zb axe # 101 & 10:00 # Stop oscillating S/C # 102 & 00:00 # Start oscillating S/C around Xb axe # 102 & 10:00 # Stop oscillating S/C # 102 & 10:01 # Roll S/C 90 degrees back to initial attitude # 114 & 00:00 # Send GBDOCL # Close door prior to injection into Halo Orbit 119 & 00:00 # Send GBDOOP # Open door & start continuous routine Obs. ; end of file ; Control Files to be used shall be up-dated versions of (used in air) ; MMS ELISA existing ones. ; Regards Jacques Charra