|
![]() |
|
![]() |
(a) Weather decks. If a deck load (such as lumber or other smooth sided deck cargo) more than five feet (1.52 m) high is stowed within three feet (.91 m) of the hatch coaming and employees handling hatch beams and hatch covers are not protected by a coaming at least 24-inch (.61 m) high, a taut handline shall be provided along the side of the deckload. The requirements of §1918.35 are not intended to apply in this situation. (b) Intermediate decks. (1) There shall be a three-foot (.91 m) working space between the stowed cargo and the coaming at both sides and at one end of the hatches with athwartship hatch beams, and at both ends of those hatches with fore and aft hatch beams, before intermediate deck hatch covers and hatch beams are removed or replaced. Exception: The three-foot (.91 m) clearance is not required on the covered portion of a partially open hatch, nor is it required when lower decks have been filled to hatch beam height with cargo of such a nature as to provide a safe surface upon which employees may work. (2) For purposes of paragraph (b)(1) of this section, fitted gratings that are in good condition shall be considered a part of the decking when properly placed within the three-foot (.91 m) area. (c) Grab rails or taut handlines shall be provided for the protection of employees handling hatch beams and hatch covers, when bulkheads, lockers, reefer compartments or large spare parts are within three feet (.91 m) of the coaming. (d) The clearances in this section do not apply to hatches opened or closed solely by hydraulic or other mechanical means; except that, in all cases in which the three-foot (.91 m) clearance does not exist, cargo that is stowed within three feet (.91 m) of the edge of the hatch shall be adequately secured to prevent cargo from falling into the hold. [62 FR 40202, July 25, 1997, as amended at 65 FR 40944, June 30, 2000] § 1918.42 Hatch beam and pontoon bridles.(a) Hatch beam and pontoon bridles shall be: (1) Long enough to reach the holes, rings, or other lifting attachments on the hatch beams and pontoons easily; (2) Of adequate strength to lift the load safely; and (3) Properly maintained, including covering or blunting of protruding ends in wire rope splices. (b) Bridles for lifting hatch beams shall be equipped with toggles, shackles, or hooks, or other devices of such design that they cannot become accidentally dislodged from the hatch beams with which they are used. Hooks other than those described in this section may be used only when they are hooked into the standing part of the bridle. Toggles, when used, shall be at least one inch (2.54 cm) longer than twice the largest diameter of the holes into which they are placed. (c) Bridles used for lifting pontoons and plugs shall have the number of legs required by the design of the pontoon or plug, and all of which shall be used. Where any use of a bridle requires fewer than the number of legs provided, idle legs shall be hung on the hook or ring, or otherwise prevented from swinging free. (d) At least two legs of all strongback and pontoon bridles shall be equipped with a lanyard at least eight feet (2.44 m) long and in good condition. The bridle end of the lanyard shall be of chain or wire. [62 FR 40202, July 25, 1997, as amended at 65 FR 40944, June 30, 2000] § 1918.43 Handling hatch beams and covers.Paragraphs (f)(2), (g), and (h) of this section apply only to folding, sliding, or hinged metal hatch covers or to those hatch covers handled by cranes. (a) (1) When hatch covers or pontoons are stowed on the weather deck abreast of hatches, they shall be arranged in stable piles not closer to the hatch coaming than three feet (.91 m). Exception: On the working side of the hatch, hatch covers or pontoons may be spread one high between the coaming and bulwark with no space between them, provided the height of the hatch coaming is no less than 24 inches (.61 m). Under no circumstances shall hatch covers or pontoons be stacked higher than the hatch coaming or bulwark on the working side of the hatch. (2) On seagoing vessels, hatch boards or similar covers removed from the hatch beams in a section of partially opened hatch during cargo handling, cleaning or other operations shall not be stowed on the boards or covers left in place within that section. (b) Hatch beams shall be laid on their sides, or stood on an edge close together and lashed. Exception: This paragraph (b) shall not apply in cases where hatch beams are of such design that: (1) The width of the flange is 50 percent or more of the height of the web; and (2) The flange rests flat on the deck when the hatch beam is stood upright. (c) Strongbacks, hatch covers, and pontoons removed from hatch openings and placed on the weather deck shall not obstruct clear fore-and-aft or coaming-to-bulwark passageways and shall be lashed or otherwise secured to prevent accidental dislodgement. Dunnage or other suitable material shall be used under and between tiers of strongbacks and pontoons to prevent them from sliding when stowed on steel decks. (d) Hatch covers unshipped in an intermediate deck shall be placed at least three feet (.91 m) from the coaming or they shall be removed to another deck. Strongbacks unshipped in an intermediate deck shall not be placed closer than six inches (15.24 cm) from the coaming and, if placed closer than three feet (.91 m), shall be secured so that they cannot be tipped or dragged into a lower compartment. If such placement or securement is not possible, strongbacks shall be removed to another deck. (e) Any hatch beam or pontoon left in place next to an open hatch section being worked shall be locked or otherwise secured, so that it cannot be accidentally displaced. All portable, manually handled hatch covers, including those bound together to make a larger cover, shall be removed from any working section, and adjacent sections, unless securely lashed. (f)(1) The roller hatch beam at the edge of the open section of the hatch shall be lashed or pinned back so that it cannot be moved toward the open section. (2) Rolling, sectional or telescopic hatch covers of barges that open in a fore and aft direction shall be secured against unintentional movement while in the open position. (g) Hinged or folding hatch covers normally stowed in an approximately vertical position shall be positively secured when in the upright position, unless the design of the system otherwise prevents unintentional movement. (h) Hatches shall not be opened or closed while employees are in the square of the hatch below. (i) All materials such as dunnage, lashings, twist locks, or stacking cones shall be removed from the hatch cover or be secured to prevent them from falling off the cover before the hatch cover is moved. (j) When a hatch is to be covered, hatch covers or night tents shall be used. Any covering that only partially covers the hatch, such as alternate hatch covers or strips of dunnage, shall not be covered by a tarpaulin. Exception: A tarpaulin may be used to cover an open or partially open hatch to reduce dust emissions during bulk cargo loading operations, if positive means are taken to prevent employees from walking on the tarpaulin. [62 FR 40202, July 25, 1997, as amended at 65 FR 40944, June 30, 2000] Browse Previous | Browse Next
|