#!/usr/bin/perl
#
# Copyright (C) 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
# Yokogawa Electric Corporation.
# All rights reserved.
# 
# Redistribution and use of this software in source and binary
# forms, with or without modification, are permitted provided that
# the following conditions and disclaimer are agreed and accepted
# by the user:
# 
# 1. Redistributions of source code must retain the above copyright
#    notice, this list of conditions and the following disclaimer.
# 
# 2. Redistributions in binary form must reproduce the above copyright
#    notice, this list of conditions and the following disclaimer in
#    the documentation and/or other materials provided with
#    the distribution.
# 
# 3. Neither the names of the copyrighters, the name of the project
#    which is related to this software (hereinafter referred to as
#    "project") nor the names of the contributors may be used to
#    endorse or promote products derived from this software without
#    specific prior written permission.
# 
# 4. No merchantable use may be permitted without prior written
#    notification to the copyrighters.
# 
# 5. The copyrighters, the project and the contributors may prohibit
#    the use of this software at any time.
# 
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHTERS, THE PROJECT AND
# CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING
# BUT NOT LIMITED THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
# FOR A PARTICULAR PURPOSE, ARE DISCLAIMED.  IN NO EVENT SHALL THE
# COPYRIGHTERS, THE PROJECT OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
# INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
# (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
# SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
# HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
# STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
# IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
# POSSIBILITY OF SUCH DAMAGE.
#
# $Id: IKEv2-SGW-I-1-1-1-2.seq,v 1.3 2008/11/28 10:16:24 doo Exp $
#
################################################################

BEGIN
{
	push(@INC, '..');
	$ENV{'V6EVAL_WITH_KOI'} = 'TRUE';
}

END {}



use V6evalTool;
use IKEv2v6eval;
use IKEv2;
use strict;



my $remote	= 'common_remote_index';
my $selector	= 'common_selector_index_outbound';

my $session	= undef;
my $ret	= undef;
my $str = undef;
my $expected_ike_sa_init_request	= undef;
my $ike_sa_init_req_param = undef;
my $ike_sa_init_resp_param = undef;
my $ike_auth_req_param = undef;
my $material	= undef;



kLogHTML('<FONT COLOR="#FF0000" SIZE="+1"><U><B>TEST SETUP</B></U></FONT>');



#------------------------------#
# register IKEv2.pm            #
#------------------------------#
unless(IKEv2initialize('SGW', 'SGW')) {
	IKEv2exitFatal('<FONT COLOR="#ff0000">IKEv2 module initializing failure</FONT>');
}



#------------------------------#
# configure TN                 #
#------------------------------#
unless(IKEv2setupTN()) {
	IKEv2exitFatal('<FONT COLOR="#ff0000">TN setup failure</FONT>');
}



#------------------------------#
# configure NUT                #
#------------------------------#
unless(IKEv2setupNUT()) {
	IKEv2exitFatal('<FONT COLOR="#ff0000">NUT setup failure</FONT>');
}



kLogHTML('<FONT COLOR="#FF0000" SIZE="+1"><U><B>TEST PROCEDURE</B></U></FONT>');



#------------------------------#
# prepare session handler      #
#------------------------------#
$session = IKEv2create_session($remote);
unless(defined($session)) {
	IKEv2exitFatal('<FONT COLOR="#ff0000">IKEv2 session creation failure</FONT>');
}



#--------------------------------------#
# invoke IKE_SA_INIT request by NUT    #
#--------------------------------------#
unless(IKEv2initiateNUT($selector)) {
	IKEv2exitFatal('<FONT COLOR="#ff0000">NUT initiation failure</FONT>');
}



#--------------------------------------#
# receive IKE_SA_INIT request by NUT   #
#--------------------------------------#
$str  = '<PRE>';
$str .= "    (I)             (R)\n";
$str .= "    NUT             TN1\n";
$str .= "     |               |\n";
$str .= "     |-------------->| IKE_SA_INIT request (HDR, SAi1, KEi, Ni)\n";
$str .= "     |               |\n";
$str .= "     V               V";
$str .= '</PRE>';

kLogHTML($str);


$ike_sa_init_req_param = devel_IKEv2receive_IKE_SA_INIT_request($session, $remote);
unless(defined($ike_sa_init_req_param)) {
	kLogHTML(kDump_Common_Error());
	kLogHTML('<FONT COLOR="#ff0000">Can\'t observe IKE_SA_INIT request.</FONT>');
	IKEv2exitFail();
}



#--------------------------------------#
# send IKE_SA_INIT response            #
#--------------------------------------#
$str  = '<PRE>';
$str .= "    (I)             (R)\n";
$str .= "    NUT             TN1\n";
$str .= "     |               |\n";
$str .= "     |<--------------| IKE_SA_INIT response (HDR, SAr1, KEr, Nr)\n";
$str .= "     |               |\n";
$str .= "     V               V";
$str .= '</PRE>';

kLogHTML($str);



$ike_sa_init_resp_param = devel_IKEv2send_IKE_SA_INIT_response($session, $remote, $ike_sa_init_req_param);
unless(defined($ike_sa_init_resp_param)) {
	kLogHTML(kDump_Common_Error());
	IKEv2exitFatal('<FONT COLOR="#ff0000">Can\'t send IKE_SA_INIT response.</FONT>');
}



#--------------------------------------#
# generate keying material             #
#--------------------------------------#
$material = devel_IKEv2gen_keymat(0, # Responder
				  $ike_sa_init_req_param,
				  $ike_sa_init_resp_param);
unless(defined($material)) {
	kLogHTML(kDump_Common_Error());
	IKEv2exitFatal('<FONT COLOR="#ff0000">Can\'t generate keying material.</FONT>');
}



#--------------------------------------#
# prepare IKE_AUTH request             #
#--------------------------------------#
my $common_exp_ike_auth_req = $exp_ike_auth_req->{'common_remote_index'};
my @my_exp_ike_auth_req = @{$common_exp_ike_auth_req};
foreach my $payload (@my_exp_ike_auth_req) {
	if ($payload->{'self'} eq 'E') {
		my @payloads = grep {
			my $ret = 0;
			if ($_->{'self'} ne 'N') { $ret = 1; }
			if ($_->{'type'} ne 'USE_TRANSPORT_MODE') { $ret = 1; }
			$ret;
		} @{$payload->{'innerPayloads'}};

		$payload->{'innerPayloads'} = \@payloads;
	}
}
# set correct nexttype
for (my $i = 0; $i < scalar(@my_exp_ike_auth_req); $i++) {
	my $payload = $my_exp_ike_auth_req[$i];

	if ($payload->{'self'} eq 'E') {
		for (my $j = 0; $j < scalar(@{$payload->{'innerPayloads'}}); $j++) {
			my $cur = $payload->{'innerPayloads'}->[$j];
			my $next = $payload->{'innerPayloads'}->[$j+1];
			unless (defined($next)) {
				$cur->{'nexttype'} = '0';
				next;
			}
			if ($cur->{'nexttype'} eq $next->{'self'}) {
				next;
			}
			$cur->{'nexttype'} = $next->{'self'};
		}

		next;
	}
}

my $exp_index = 'SGW-I-1-1-1-2.1';
$exp_ike_auth_req->{$exp_index} = \@my_exp_ike_auth_req;



#--------------------------------------#
# receive IKE_AUTH request by NUT      #
#--------------------------------------#
$str  = '<PRE>';
$str .= "    (I)             (R)\n";
$str .= "    NUT             TN1\n";
$str .= "     |               |\n";
$str .= "     |-------------->| IKE_AUTH request (HDR, SK {IDi, AUTH, SAi2, TSi, TSr)\n";
$str .= "     |               |\n";
$str .= "     V               V";
$str .= '</PRE>';

kLogHTML($str);



$ike_auth_req_param = devel_IKEv2receive_IKE_AUTH_request($session,
							$exp_index,
							$ike_sa_init_req_param,
							$ike_sa_init_resp_param,
							$material);
unless(defined($ike_auth_req_param)) {
	kLogHTML(kDump_Common_Error());
	kLogHTML('<FONT COLOR="#ff0000">Can\'t observe IKE_AUTH request.</FONT>');
	IKEv2exitFail();
}



#--------------------------------------#
# exit with cleanup                    #
#--------------------------------------#
IKEv2exitPass();



#
# perldoc
#
########################################################################
__END__

=head1 Title

  Test IKEv2.SGW.I.1.1.1.2: Sending IKE_AUTH request
  Part A: IKE Header Format (BASIC)
  Part B: Encrypted Payload Format (BASIC)
  Part C: IDi Payload Format (BASIC)
  Part D: AUTH Payload Format (BASIC)
  Part E: SA Payload Format (BASIC)
  Part F: TSi Payload Format (BASIC)
  Part G: TSr Payload Format (BASIC)

=head1 Purpose

  To verify an IKEv2 device transmits IKE_AUTH request using properly Header and
  Payloads format

=head1 References

  * [RFC 4306] - Sections 1.2, 2.15, 3.1, 3.2, 3.3, 3.5, 3.8, 3.10, 3.13 and 3.14

=head1 Test Setup

  * Network Topology
      Connect the devices according to the Common Topology.
  * Configuration
      In each part, configure the devices according to the Common Configuration.
  * Pre-Sequence and Cleanup Sequence
      IKEv2 on the NUT is disabled after each part.

=head1 Procedure

=begin html
<BLOCKQUOTE>
<PRE>
   NUT                  TN1
  (SGW)                (SGW)
    |                    |
    |------------------->| IKE_SA_INIT request (HDR, SAi1, KEi, Ni)
    |                    | (Judgement #1)
    |<-------------------| IKE_SA_INIT response (HDR, SAr1, KEr, Nr) 
    |                    | (Packet #1)
    |                    | 
    |------------------->| IKE_AUTH request (HDR, SK {IDi, AUTH, SAi2, TSi, TSr})
    |                    | (Judgement #2)
    |                    | 
    V                    V
<br>
<BLOCKQUOTE>
<TABLE BORDER>
<TR>
<TD><TT>Packet #1</TT></TD>
<TD><TT>See Common Packet #2</TT></TD>
</TR>
</TABLE>  
</BLOCKQUOTE>
</BLOCKQUOTE>
</PRE>

=end html 

  Part A: IKE Header Format (BASIC)
     1. NUT starts to negotiate with TN1 by sending IKE_SA_INIT request.
     2. Observe the messages transmitted on Link A.
     3. TN1 responds with an IKE_SA_INIT response to the NUT.
     4. Observe the messages transmitted on Link A.

  Part B: Encrypted Payload Format (BASIC)
     5. NUT starts to negotiate with TN1 by sending IKE_SA_INIT request.
     6. Observe the messages transmitted on Link A.
     7. TN1 responds with an IKE_SA_INIT response to the NUT.
     8. Observe the messages transmitted on Link A.

  Part C: IDi Payload Format (BASIC)
     9. NUT starts to negotiate with TN1 by sending IKE_SA_INIT request.
     10. Observe the messages transmitted on Link A.
     11. TN1 responds with an IKE_SA_INIT response to the NUT.
     12. Observe the messages transmitted on Link A.

  Part D: AUTH Payload Format (BASIC)
     13. NUT starts to negotiate with TN1 by sending IKE_SA_INIT request.
     14. Observe the messages transmitted on Link A.
     15. TN1 responds with an IKE_SA_INIT response to the NUT.
     16. Observe the messages transmitted on Link A.

  Part E: SA Payload Format (BASIC)
     17. NUT starts to negotiate with TN1 by sending IKE_SA_INIT request.
     18. Observe the messages transmitted on Link A.
     19. TN1 responds with an IKE_SA_INIT response to the NUT.
     20. Observe the messages transmitted on Link A.

  Part F: TSi Payload Format (BASIC)
     21. NUT starts to negotiate with TN1 by sending IKE_SA_INIT request.
     22. Observe the messages transmitted on Link A.
     23. TN1 responds with an IKE_SA_INIT response to the NUT.
     24. Observe the messages transmitted on Link A.

  Part G: TSr Payload Format (BASIC)
     25. NUT starts to negotiate with TN1 by sending IKE_SA_INIT request.
     26. Observe the messages transmitted on Link A.
     27. TN1 responds with an IKE_SA_INIT response to the NUT.
     28. Observe the messages transmitted on Link A.

=head1 Observable Result

  Part A
       Step 2: Judgment #1
       The NUT transmits an IKE_SA_INIT request including "ENCR_3DES",
       "PRF_HMAC_SHA1", "AUTH_HMAC_SHA1_96" and "D-H group 2" as proposed
       algorithms.

       Step 4: Judgment #2
       The NUT transmits an IKE_AUTH request including properly formatted IKE Header
       containing following values:

=begin html

<BLOCKQUOTE>
<PRE>
                           1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                      IKE_SA Initiator s SPI                   !
      !                                                               !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                      IKE_SA Responder s SPI                   !
      !                                                               !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !  Next Payload ! MjVer ! MnVer ! Exchange Type !     Flags     !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                            Message ID                         !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                              Length                           !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 
                          Figure 106 Header format<br>
 
    * An IKE_SA Initiator's SPI field set to same as the IKE_SA_INIT request's IKE_SA
      Initiator's SPI field value.
    * An IKE_SA Responder's SPI field set to same as the IKE_SA_INIT response's
      IKE_SA Responder's SPI field value.
    * A Next Payload field set to Encrypted Payload (46).
    * A Major Version field set to 2.
    * A Minor Version field set to zero.
    * An Exchange Type field set to IKE_AUTH (35).
    * A Flags field set to (00010000)2 = (16)10.
    * A Message ID field set to 1.
    * A Length field set to the length of the message (header + payloads) in octets.


</PRE>
</BLOCKQUOTE>

=end html

  
  
  Part B
       Step 6: Judgment #1
       The NUT transmits an IKE_SA_INIT request including "ENCR_3DES",
       "PRF_HMAC_SHA1", "AUTH_HMAC_SHA1_96" and "D-H group 2" as proposed
       algorithms.

       Step 8: Judgment #2
       The NUT transmits an IKE_AUTH request including properly formatted Encrypted Payload
       containing following values:

=begin html

<BLOCKQUOTE>
<PRE>

                           1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      ! Next Payload  !C!  RESERVED   !         Payload Length        !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                     Initialization Vector                     !
      !         (length is block size for encryption algorithm)       !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      ~                    Encrypted IKE Payloads                     ~
      +               +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !               !             Padding (0-255 octets)            !
      +-+-+-+-+-+-+-+-+                               --+-+-+-+-+-+-+-+
      !                                               !  Pad Length   !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      ~                    Integrity Checksum Data                    ~   
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
  
                        Figure 107 Encrypted payload<br>
    
    * A Next Payload field set to IDi Payload (35).
    * A Critical field set to zero.
    * A RESERVED field set to zero.
    * A Payload Length field set to length in octets of the header, IV, Encrypted IKE
      Payloads, Padding, Pad Length, and Integrity Check sum Data.
    * An Initialization Vector field set to a randomly chosen value whose length is
      equal to the block length of the underlying encryption algorithm. It is 64 bits
      length in ENCR_3DES case.
    * An Encrypted IKE Payloads field set to subsequent payloads encrypted by
      ENCR_3DES.
    * A Padding field set to any value which to be a multiple of the encryption block
      size. It is 64 bits length in ENCR_3DES case.
    * A Pad Length field set to the length of the Padding field.
    * An Integrity Checksum Data set to the cryptographic checksum of the entire
      message. It is 96 bits length in AUTH_HMAC_SHA1_96 case. The checksum
      must be valid by calculation according to the manner described in RFC.
 
</PRE>
</BLOCKQUOTE>

=end html

  
  
  Part C
       Step 10: Judgment #1
       The NUT transmits an IKE_SA_INIT request including "ENCR_3DES",
       "PRF_HMAC_SHA1", "AUTH_HMAC_SHA1_96" and "D-H group 2" as proposed
       algorithms.

       Step 12: Judgment #2
       The NUT transmits an IKE_AUTH request including properly formatted ID Payload
       containing following values:

=begin html

<BLOCKQUOTE>
<PRE>
                           1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      ! Next Payload  !C!  RESERVED   !         Payload Length        ! 
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !   ID Type     !              RESERVED                         !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                                                               !
      ~                   Identification Data                         ~ 
      !                                                               !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<br>
                       Figure 108 ID Payload format<br>
    
    * A Next Payload field set to AUTH Payload (39).
    * A Critical field set to zero.
    * A RESERVED field set to zero.
    * A Payload Length field set to length of the current payload. It is 24 bytes for
      ID_IPV6_ADDR.
    * An ID Type field set to ID_IPV6_ADDR (5).
    * A RESERVED field set to zero.
    * An Identification Data field set to the NUT address.

</PRE>
</BLOCKQUOTE>

=end html

  
  
  Part D
       Step 14: Judgment #1
       The NUT transmits an IKE_SA_INIT request including "ENCR_3DES",
       "PRF_HMAC_SHA1", "AUTH_HMAC_SHA1_96" and "D-H group 2" as proposed
       algorithms.

       Step 16: Judgment #2
       The NUT transmits an IKE_AUTH request including properly formatted AUTH Payload
       containing following values:

=begin html

<BLOCKQUOTE>
<PRE>
                           1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      ! Next Payload  !C!  RESERVED   !         Payload Length        !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      ! Auth Method   !              RESERVED                         !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                                                               !
      ~                    Authentication  Data                       ~  
      !                                                               !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    
                       Figure 109 AUTH Payload format<br>
     
    * A Next Payload field set to SA Payload (33).
    * A Critical field set to zero.
    * A RESERVED field set to zero.
    * A Payload Length field set to length of the current payload. It is 28 bytes for
      PRF_HMAC_SHA1.
    * An Auth Method field set to Shared Key Message Integrity Code (2).
    * A RESERVED field set to zero.
    * An Authentication Data field set to correct authentication value according to the
      manner described in RFC. It is 160 bytes length in PRF_HMAC_SHA1 case.

</PRE>
</BLOCKQUOTE>

=end html

  
  
  Part E
       Step 18: Judgment #1
       The NUT transmits an IKE_SA_INIT request including "ENCR_3DES",
       "PRF_HMAC_SHA1", "AUTH_HMAC_SHA1_96" and "D-H group 2" as proposed
       algorithms.

       Step 20: Judgment #2

=begin html

<BLOCKQUOTE>
<PRE>

                                   1                   2                   3
               0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
              +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+--------------
              ! Next    44    !0!      0      ! Length          40            !             |
              +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+---          |
              !       0       !       0       ! Length          36            !  |          |
              +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  |          |
              ! Number    1   ! Prot ID   3   ! SPI Size  4   ! Trans Cnt  3  !  |          |
              +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  |          |
              ! SPI value                                                     !  |          |
          --- +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  |          |
           |  !       3       !       0       ! Length           8            !  |          | 
 Transform |  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  |          |SA Payload 
           |  ! Type  1  (EN) !       0       ! Transform ID     3     (3DES) !  | Proposal |
          --- +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  |          |
           |  !       3       !       0       ! Length           8            !  |          |
 Transform |  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  |          |
           |  ! Type  3  (IN) !       0       ! Transform ID     2     (SHA1) !  |          |
          --- +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  |          |
           |  !       0       !       0       ! Length           8            !  |          |
 Transform |  +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  |          |
           |  ! Type  5  (ESN)!       0       ! Transform ID     0       (No) !  |          |
          --- +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  |          |<br>
                                 Figure 110 SA Payload contents
</PRE>
</BLOCKQUOTE>

=end html

=begin html
<BLOCKQUOTE>
<PRE>
              The NUT transmits an IKE_AUTH request including properly formatted SA Payload
              containing following values (refer following figures):<br>
    
                                  1                   2                   3
              0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
             +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
             ! Next Payload  !C!  RESERVED   !         Payload Length        !
             +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
             !                                                               !
             ~                        &lt;Proposals>                            ~
             !                                                               !
             +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<br>
    
                                Figure 111 SA Payload format 
<br>
                    * A Next Payload field set to TSi Payload (44).
                    * A Critical field set to zero.
                    * A RESERVED field set to zero.
                    * A Payload Length field set to length of the current payload.
</PRE>
</BLOCKQUOTE>

=end html 

=begin html
<BLOCKQUOTE>
<PRE>
  
             The following proposal must be included in Proposals field.
      
                                 1                   2                   3
             0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
            +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
            ! 0 (last) or 2 !   RESERVED    !         Proposal Length       !
            +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
            ! Proposal #    !  Protocol ID  !    SPI Size   !# of Transforms!
            +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
            !                        SPI (variable)                         !
            +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
            !                                                               !
            ~                         &lt;Transforms>                          ~
            !                                                               !
            +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<br>
   
                          Figure 112 Proposal sub-structure format 
<br>
     Proposal #1
    
      * A 0 or 2 field set to zero if this structure is the last proposal, otherwise set to 2.
      * A RESREVD field set to zero.
      * A Proposal Length field set to length of this proposal, including all transforms
        and attributes. It is 36 bytes according to Common Configuration.
      * A Proposal # field set to 1 if this structure is the first proposal, otherwise set to 1
        greater thatn the previous proposal.
      * A Protocol ID field set to ESP (3).
      * A SPI Size field set to 4.
      * A # of Transforms field set to 3.
      * A SPI field set to the sending entity's SPI (4 octets value)
</Pre>
</BLOCKQUOTE>

=end html

=begin html
<BLOCKQUOTE>
<PRE>
   
         A Transform field is set to following (There are 4 Transform Structures).
<br>
                                 1                   2                   3
             0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
            +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
            ! 0 (last) or 3 !   RESERVED    !       Transform Length        !
            +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
            !Transform Type !   RESERVED    !          Transform ID         !
            +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
            !                                                               !
            ~                      Transform Attributes                     !
            !                                                               !
            +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<br>
                          Figure 113 Transform sub-structure format 
<br>
     Transform #1
      * A 0 or 3 field set to zero if this structure is the last transform, otherwise set to 3.
      * A RESERVED field set to zero.
      * A Transform Length set to length of the Transform Substructure including
        Header and Attribute. It is 8 bytes for ENCR_3DES.
      * A Transform Type field set to ENCR (1).
      * A RESERVED field set to zero.
      * A Transform ID set to ENCR_3DES (3).
<br>
     Transform #2
      * A 0 or 3 field set to zero if this structure is the last transform, otherwise set to 3.
      * A RESERVED field set to zero.
      * A Transform Length set to length of the Transform Substructure including
        Header and Attribute. It is 8 bytes for AUTH_HMAC_SHA1.
      * A Transform Type field set to INTEG (3).
      * A RESERVED field set to zero.
      * A Transform ID set to AUTH_HMAC_SHA1 (2).
<br>
     Transform #3
      * A 0 or 3 field set to zero if this structure is the last transform, otherwise set to 3.
      * A RESERVED field set to zero.
      * A Transform Length set to length of the Transform Substructure including
        Header and Attribute. It is 8 bytes for ESN.
      * A Transform Type field set to ESN (5).
      * A RESERVED field set to zero.
      * A Transform ID set to No Extended Sequence Numbers (0).
</Pre>
</BLOCKQUOTE>

=end html

  
  
  Part F
       Step 22: Judgment #1
       The NUT transmits an IKE_SA_INIT request including "ENCR_3DES",
       "PRF_HMAC_SHA1", "AUTH_HMAC_SHA1_96" and "D-H group 2" as proposed
       algorithms.

       Step 24: Judgment #2
       The NUT transmits an IKE_AUTH request including properly formatted TSi Payload
       containing following values:

=begin html

<BLOCKQUOTE>
<PRE>
  
                           1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      ! Next Payload  !C!  RESERVED   !         Payload Length        !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      ! Number of Tss !                 RESERVED                      !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                                                               !
      ~                       &lt;Traffic Selector>                      ~
      !                                                               !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<br>
                        Figure 114 TSi Payload format<br>
   
      * A Next Payload field set to TSr Payload (45).
      * A Critical field set to zero.
      * A RESERVED field set to zero.
      * A Payload Length field set to length of the current payload.
      * A Number of TSs field set to the number of actual traffic selectors.
      * A RESERVED field set to zero.

</PRE>
</BLOCKQUOTE>

=end html

=begin html

<BLOCKQUOTE>
<PRE>
   
    The following traffic selector must be included in Traffic Selectors field.
<br>
                           1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !   TS Type     !IP Protocol ID*|       Selector  Length        | 
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !           Start Port*         |            End Port*          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                                                               !
      -                       Starting Address*                       -
      !                                                               !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                                                               !
      -                         Ending Address*                       - 
      !                                                               !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<br>
                        Figure 115 Traffic Selector <br>
    
      * A TS Type set to TS_IPV6_ADDR_RANGE (8).
      * An IP Protocol ID field set to zero.
      * A Selector Length field set to length of this Traffic Selector Substructure
        including the header. It is 40 bytes for TS_IPV6_ADDR_RANGE.
      * A Start Port field set to zero.
      * An End Port field set to 65535.
      * A Starting Address field set to less than or equal to Prefix B.
      * A Ending Address field set to greater thatn or equal to Prefix B.

</PRE>
</BLOCKQUOTE>

=end html

  
  
  Part G
       Step 26: Judgment #1
       The NUT transmits an IKE_SA_INIT request including "ENCR_3DES",
       "PRF_HMAC_SHA1", "AUTH_HMAC_SHA1_96" and "D-H group 2" as proposed
       algorithms.

       Step 28: Judgment #2
       The NUT transmits an IKE_AUTH request including properly formatted TSr Payload
       containing following values:

=begin html

<BLOCKQUOTE>
<PRE>
   
                           1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      ! Next Payload  !C!  RESERVED   !         Payload Length        !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      ! Number of TSs !                 RESERVED                      !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                                                               !
      ~                       &lt;Traffic Selectors>                     ~
      !                                                               !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<br>
                        Figure 116 TSi Payload format<br>
   
          * A Next Payload field set to zero.
          * A Critical field set to zero.
          * A RESERVED field set to zero.
          * A Payload Length field set to length of the current payload.
          * A Number of TSs field set to the number of actual traffic selectors.
          * A RESERVED field set to zero.

</PRE>
</BLOCKQUOTE>

=end html

=begin html

<BLOCKQUOTE>
<PRE>
   
    The following traffic selector must be included in Traffic Selectors field.
   
                           1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !   TS Type     !IP Protocol ID*|       Selector  Length        | 
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !           Start Port*         |            End Port*          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                                                               !
      -                       Starting Address*                       -
      !                                                               !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                                                               !
      -                         Ending Address*                       - 
      !                                                               !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<br>
                       Figure 117 Traffic Selector <br>
    
          * A TS Type set to TS_IPV6_ADDR_RANGE (8).
          * An IP Protocol ID field set to zero.
          * A Selector Length field set to length of this Traffic Selector Substructure
            including the header. It is 40 bytes for TS_IPV6_ADDR_RANGE.
          * A Start Port field set to zero.
          * An End Port field set to 65535.
          * A Starting Address field set to less than or equal to Prefix Y.
          * An Ending Address field set to less than or equal to Prefix Y.

</PRE>
</BLOCKQUOTE>

=end html

=head1 Possible Problems

    * IKE_AUTH request has following packet format.It may have additional payloads
      described below. Additional payloads can be ignored by this test. The order of payload
      may be different from this sample.

=begin html

<BLOCKQUOTE>
<PRE>
<br>   
          IDi,
          [CERT+],
          [N(INITIAL_CONTACT)],
          [[N(HTTP_CERT_LOOKUP_SUPPORTED)], CERTREQ+],
          [IDr],
          AUTH,
          [CP(CFG_REQUEST)],
          [N(IPCOMP_SUPPORTED)+],
          [N(USE_TRANSPORT_MODE)],
          [N(ESP_TFC_PADDING_NOT_SUPPORTED)],
          [N(NON_FIRST_FRAGMENTS_ALSO)],
          SA,
          TSi,
          TSr,
          [V+]
<br>   
</PRE>
</BLOCKQUOTE>

=end html

    * The implementation may not set single proposal by the implementation policy. In this
      case, Security Association Payload contains multiple proposals.

    * Each of transforms can be located in the any order.

    * The implementation may not set single traffic selector by the implementation policy. In
      this case, Traffic Selector Payload contains multiple proposals.

=cut

