# uname -a Linux web1 2.4.21-4.0.1.EL-smp-static-aacraid #4 SMP Thu Dec 18 10:22:13 CET 2003 i686 i686 i386 GNU/Linux # cat /proc/scsi/aacraid/0 Adaptec Raid Controller 1.1-4 Dec 18 2003 10:23:04 Vendor: DELL Model: PERCRAID kernel: 2.7-4[3170] monitor: 2.7-4[3170] bios: 2.7-0[3170] serial: fef010d3 # afacli ... COMMAND: controller list Executing: controller list Adapter Name Adapter Type Availability Clustering ------------ ------------ ------------ ------------ afa0 PERC 3/Di read/write No COMMAND: controller details Executing: controller details Controller Information ---------------------- Remote Computer: . Device Name: AFA0 Controller Type: PERC 3/Di Access Mode: READ-WRITE Controller Serial Number: Last Six Digits = F010D3 Number of Buses: 2 Devices per Bus: 15 Controller CPU: i960 R series Controller CPU Speed: 100 Mhz Controller Memory: 128 Mbytes Battery State: Ok Component Revisions ------------------- CLI: 2.7-1 (Build #4944) API: 2.7-1 (Build #4944) Miniport Driver: 1.1-0 (Build #9999) Controller Software: 2.7-1 (Build #3170) Controller BIOS: 2.7-1 (Build #3170) Controller Firmware: (Build #3170) COMMAND: controller show channels Executing: controller show channels Ch# Host ID Targets Type Max Usage --- ------- ------- --------- --------- 0 7 15 Ultra160 NoInfo 1 7 15 Ultra160 NoInfo COMMAND: container list /full=TRUE Executing: container list /full=TRUE Num Total Oth Chunk Scsi Partition Creation System Label Type Size Ctr Size Usage B:ID:L Offset:Size State RO Lk Task Done% Ent Date Time Files ----- ------ ------ --- ------ ------- ------ ------------- ------- -- -- ------- ------ --- ------ -------- ------ 0 RAID-5 136GB 64KB Open 0:00:0 64.0KB:68.3GB 0 121503 12:55:14 /dev/sda RAID5DATA 0:01:0 64.0KB:68.3GB 1 121503 12:55:14 0:02:0 64.0KB:68.3GB 2 121503 12:55:14 COMMAND: disk list /full=TRUE Executing: disk list /full=TRUE B:ID:L Device Type Removable media Vendor-ID Product-ID Rev Blocks Bytes/Block Usage Shared Rate ------ -------------- --------------- --------- ---------------- ----- --------- ----------- ---------------- ------ ---- 0:00:0 Disk N MAXTOR ATLAS10K4_73SCA DFM0 143374650 512 Initialized NO 160 0:01:0 Disk N MAXTOR ATLAS10K4_73SCA DFM0 143374650 512 Initialized NO 160 0:02:0 Disk N MAXTOR ATLAS10K4_73SCA DFM0 143374650 512 Initialized NO 160 0:03:0 Disk N MAXTOR ATLAS10K4_73SCA DFM0 143374650 512 Initialized NO 160 COMMAND: enclosure list /full=TRUE Executing: enclosure list /full=TRUE Enclosure ID (B:ID:L) Fan Power Slot Sensor Door Speaker Standard Diagnostic EnclosureId VendorId ProductId Firmware ----------- --- ----- ---- ------ ---- -------- -------- ---------- ---------------- -------- ---------------- -------- 0 0:06:0 0 0 5 2 0 No SAF-TE PASSED 1983a190a0000d5 PE/PV 1x5 SCSI BP 1.1 COMMAND: enclosure show slot Executing: enclosure show slot # cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Xeon(TM) CPU 2.80GHz stepping : 9 cpu MHz : 2787.936 cache size : 512 KB physical id : 0 siblings : 2 runqueue : 0 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm bogomips : 5557.45 processor : 1 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Xeon(TM) CPU 2.80GHz stepping : 9 cpu MHz : 2787.936 cache size : 512 KB physical id : 3 siblings : 2 runqueue : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm bogomips : 5570.56 processor : 2 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Xeon(TM) CPU 2.80GHz stepping : 9 cpu MHz : 2787.936 cache size : 512 KB physical id : 0 siblings : 2 runqueue : 0 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm bogomips : 5570.56 processor : 3 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Xeon(TM) CPU 2.80GHz stepping : 9 cpu MHz : 2787.936 cache size : 512 KB physical id : 3 siblings : 2 runqueue : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm bogomips : 5570.56 # dmesg 000 __va_range(0xfdc84, 0x74): idx=33 mapped at fffdd000 ACPI table found: FACP v1 [DELL PE2650 0.1] __va_range(0xfdcf8, 0x24): idx=33 mapped at fffdd000 __va_range(0xfdcf8, 0x88): idx=33 mapped at fffdd000 ACPI table found: APIC v1 [DELL PE2650 0.1] __va_range(0xfdcf8, 0x88): idx=33 mapped at fffdd000 LAPIC (acpi_id[0x0001] id[0x0] enabled[1]) CPU 0 (0x0000) enabledProcessor #0 Pentium 4(tm) XEON(tm) APIC version 20 LAPIC (acpi_id[0x0002] id[0x6] enabled[1]) CPU 1 (0x0600) enabledProcessor #6 Pentium 4(tm) XEON(tm) APIC version 20 LAPIC (acpi_id[0x0003] id[0x1] enabled[1]) CPU 2 (0x0100) enabledProcessor #1 Pentium 4(tm) XEON(tm) APIC version 20 LAPIC (acpi_id[0x0004] id[0x7] enabled[1]) CPU 3 (0x0700) enabledProcessor #7 Pentium 4(tm) XEON(tm) APIC version 20 IOAPIC (id[0x8] address[0xfec00000] global_irq_base[0x0]) IOAPIC (id[0x9] address[0xfec01000] global_irq_base[0x10]) IOAPIC (id[0xa] address[0xfec02000] global_irq_base[0x20]) LAPIC_NMI (acpi_id[0x0001] polarity[0x1] trigger[0x1] lint[0x1]) LAPIC_NMI (acpi_id[0x0002] polarity[0x1] trigger[0x1] lint[0x1]) LAPIC_NMI (acpi_id[0x0003] polarity[0x1] trigger[0x1] lint[0x1]) LAPIC_NMI (acpi_id[0x0004] polarity[0x1] trigger[0x1] lint[0x1]) 4 CPUs total Local APIC address fee00000 __va_range(0xfdd80, 0x24): idx=33 mapped at fffdd000 __va_range(0xfdd80, 0x50): idx=33 mapped at fffdd000 ACPI table found: SPCR v1 [DELL PE2650 0.1] Enabling the CPU's according to the ACPI table Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: DELL Product ID: PE 0121 APIC at: 0xFEE00000 I/O APIC #8 Version 17 at 0xFEC00000. I/O APIC #9 Version 17 at 0xFEC01000. I/O APIC #10 Version 17 at 0xFEC02000. Processors: 4 xAPIC support is present Enabling APIC mode: Flat. Using 3 I/O APICs Kernel command line: ro root=/dev/sda2 Initializing CPU#0 Detected 2787.936 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 5557.45 BogoMIPS Memory: 1026404k/1048448k available (1615k kernel code, 18464k reserved, 1021k data, 348k init, 130944k highmem) Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode cache hash table entries: 65536 (order: 7, 524288 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 65536 (order: 6, 262144 bytes) Page-cache hash table entries: 262144 (order: 8, 1048576 bytes) CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 CPU: Common caps: bfebfbff 00000000 00000000 00000000 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 CPU: Common caps: bfebfbff 00000000 00000000 00000000 CPU0: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09 per-CPU timeslice cutoff: 1463.02 usecs. task migration cache decay timeout: 10 msecs. enabled ExtINT on CPU#0 ESR value before enabling vector: 00000040 ESR value after enabling vector: 00000000 Booting processor 1/1 eip 2000 Initializing CPU#1 masked ExtINT on CPU#1 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Calibrating delay loop... 5570.56 BogoMIPS CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K ACPI tables and CPU MSR values mismatch about cpu number CPU: Physical Processor ID: 3 Intel machine check reporting enabled on CPU#1. CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 CPU: Common caps: bfebfbff 00000000 00000000 00000000 CPU1: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09 Booting processor 2/6 eip 2000 Initializing CPU#2 masked ExtINT on CPU#2 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Calibrating delay loop... 5570.56 BogoMIPS CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 Intel machine check reporting enabled on CPU#2. CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 CPU: Common caps: bfebfbff 00000000 00000000 00000000 CPU2: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09 Booting processor 3/7 eip 2000 Initializing CPU#3 masked ExtINT on CPU#3 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Calibrating delay loop... 5570.56 BogoMIPS CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 3 Intel machine check reporting enabled on CPU#3. CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 CPU: Common caps: bfebfbff 00000000 00000000 00000000 CPU3: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09 Total of 4 processors activated (22269.13 BogoMIPS). ENABLING IO-APIC IRQs Setting 8 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 8 ... ok. Setting 9 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 9 ... ok. Setting 10 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 10 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 8-0, 8-7, 8-10, 8-11, 8-13, 10-0, 10-1, 10-2, 10-3, 10-4, 10-5, 10-6, 10-7, 10-8, 10-9, 10-10, 10-11, 10-12, 10-13, 10-14, 10-15 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 ..MP-BIOS bug: 8254 timer not connected to IO-APIC ...trying to set up timer (IRQ0) through the 8259A ... ..... (found pin 0) ...works. number of MP IRQ sources: 33. number of IO-APIC #8 registers: 16. number of IO-APIC #9 registers: 16. number of IO-APIC #10 registers: 16. testing the IO APIC....................... IO APIC #8...... .... register #00: 08000000 ....... : physical APIC id: 08 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 000F0011 ....... : max redirection entries: 000F ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 08000000 ....... : arbitration: 08 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 00F 0F 0 0 0 0 0 1 1 31 01 00F 0F 0 0 0 0 0 1 1 39 02 000 00 1 0 0 0 0 0 0 00 03 00F 0F 0 0 0 0 0 1 1 41 04 00F 0F 0 0 0 0 0 1 1 49 05 00F 0F 1 1 0 1 0 1 1 51 06 00F 0F 0 0 0 0 0 1 1 59 07 000 00 1 0 0 0 0 0 0 00 08 00F 0F 0 0 0 0 0 1 1 61 09 00F 0F 0 0 0 0 0 1 1 69 0a 000 00 1 0 0 0 0 0 0 00 0b 000 00 1 0 0 0 0 0 0 00 0c 00F 0F 0 0 0 0 0 1 1 71 0d 000 00 1 0 0 0 0 0 0 00 0e 00F 0F 0 0 0 0 0 1 1 79 0f 00F 0F 0 0 0 0 0 1 1 81 IO APIC #9...... .... register #00: 09000000 ....... : physical APIC id: 09 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 000F0011 ....... : max redirection entries: 000F ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 09000000 ....... : arbitration: 09 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 00F 0F 1 1 0 1 0 1 1 89 01 00F 0F 1 1 0 1 0 1 1 91 02 00F 0F 1 1 0 1 0 1 1 99 03 00F 0F 1 1 0 1 0 1 1 A1 04 00F 0F 1 1 0 1 0 1 1 A9 05 00F 0F 1 1 0 1 0 1 1 B1 06 00F 0F 1 1 0 1 0 1 1 B9 07 00F 0F 1 1 0 1 0 1 1 C1 08 00F 0F 1 1 0 1 0 1 1 C9 09 00F 0F 1 1 0 1 0 1 1 D1 0a 00F 0F 1 1 0 1 0 1 1 D9 0b 00F 0F 1 1 0 1 0 1 1 E1 0c 00F 0F 1 1 0 1 0 1 1 E9 0d 00F 0F 1 1 0 1 0 1 1 32 0e 00F 0F 1 1 0 1 0 1 1 3A 0f 00F 0F 1 1 0 1 0 1 1 42 IO APIC #10...... .... register #00: 0A000000 ....... : physical APIC id: 0A ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 000F0011 ....... : max redirection entries: 000F ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 0A000000 ....... : arbitration: 0A .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 000 00 1 0 0 0 0 0 0 00 02 000 00 1 0 0 0 0 0 0 00 03 000 00 1 0 0 0 0 0 0 00 04 000 00 1 0 0 0 0 0 0 00 05 000 00 1 0 0 0 0 0 0 00 06 000 00 1 0 0 0 0 0 0 00 07 000 00 1 0 0 0 0 0 0 00 08 000 00 1 0 0 0 0 0 0 00 09 000 00 1 0 0 0 0 0 0 00 0a 000 00 1 0 0 0 0 0 0 00 0b 000 00 1 0 0 0 0 0 0 00 0c 000 00 1 0 0 0 0 0 0 00 0d 000 00 1 0 0 0 0 0 0 00 0e 000 00 1 0 0 0 0 0 0 00 0f 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:0 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ12 -> 0:12 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ16 -> 1:0 IRQ17 -> 1:1 IRQ18 -> 1:2 IRQ19 -> 1:3 IRQ20 -> 1:4 IRQ21 -> 1:5 IRQ22 -> 1:6 IRQ23 -> 1:7 IRQ24 -> 1:8 IRQ25 -> 1:9 IRQ26 -> 1:10 IRQ27 -> 1:11 IRQ28 -> 1:12 IRQ29 -> 1:13 IRQ30 -> 1:14 IRQ31 -> 1:15 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 2788.0357 MHz. ..... host bus clock speed is 132.7633 MHz. cpu: 0, clocks: 1327633, slice: 265526 CPU0 cpu: 1, clocks: 1327633, slice: 265526 cpu: 2, clocks: 1327633, slice: 265526 cpu: 3, clocks: 1327633, slice: 265526 CPU1 CPU2 CPU3 cpu_sibling_map[0] = 2 cpu_sibling_map[1] = 3 cpu_sibling_map[2] = 0 cpu_sibling_map[3] = 1 mapping CPU#0's runqueue to CPU#2's runqueue. mapping CPU#1's runqueue to CPU#3's runqueue. zapping low mappings. Process timing init...done. Starting migration thread for cpu 0 Starting migration thread for cpu 1 Starting migration thread for cpu 2 Starting migration thread for cpu 3 PCI: PCI BIOS revision 2.10 entry at 0xfc91e, last bus=5 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Ignoring BAR0-3 of IDE controller 00:0f.1 PCI: Discovered primary peer bus 01 [IRQ] PCI: Discovered primary peer bus 02 [IRQ] PCI: Discovered primary peer bus 03 [IRQ] PCI: Discovered primary peer bus 04 [IRQ] PCI: Using IRQ router ServerWorks [1166/0201] at 00:0f.0 PCI->APIC IRQ transform: (B0,I4,P0) -> 19 PCI->APIC IRQ transform: (B0,I4,P1) -> 23 PCI->APIC IRQ transform: (B0,I4,P2) -> 27 PCI->APIC IRQ transform: (B3,I6,P0) -> 28 PCI->APIC IRQ transform: (B3,I8,P0) -> 29 PCI->APIC IRQ transform: (B4,I8,P0) -> 30 PCI->APIC IRQ transform: (B5,I6,P0) -> 30 PCI->APIC IRQ transform: (B5,I6,P1) -> 31 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd allocated 32 pages and 32 bhs reserved for the highmem bounces aio_setup: num_physpages = 65528 aio_setup: sizeof(struct page) = 56 Journalled Block Device driver loaded pty: 2048 Unix98 ptys configured Real Time Clock Driver v1.10e Software Watchdog Timer: 0.05, timer margin: 60 sec Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 bonding.c:v2.2.14 (June 30, 2003) bonding_init(): either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details. bond0 registered without MII link monitoring, in load balancing (round-robin) mode. bond0 registered without ARP monitoring tg3.c:v2.2 (August 24, 2003) eth0: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:56:71:47:0f eth1: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:56:71:47:10 Equalizer1996: $Revision: 1.2.1 $ $Date: 1996/09/22 13:52:00 $ Simon Janes (simon@ncm.com) Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx SvrWks CSB5: IDE controller at PCI slot 00:0f.1 SvrWks CSB5: chipset revision 147 SvrWks CSB5: not 100% native mode: will probe irqs later SvrWks CSB5: simplex device: DMA forced ide0: BM-DMA at 0x08b0-0x08b7, BIOS settings: hda:DMA, hdb:pio SvrWks CSB5: simplex device: DMA forced ide1: BM-DMA at 0x08b8-0x08bf, BIOS settings: hdc:DMA, hdd:DMA hda: TEAC CD-ROM CD-224E, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: attached ide-cdrom driver. hda: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 SCSI subsystem driver Revision: 1.00 Red Hat/Adaptec aacraid driver (1.1-4 Dec 18 2003 10:23:04) AAC0: kernel 2.7.4 build 3170 AAC0: monitor 2.7.4 build 3170 AAC0: bios 2.7.0 build 3170 AAC0: serial fef010d3 scsi0 : percraid Starting timer : 0 0 blk: queue c3697018, I/O limit 4095Mb (mask 0xffffffff) Vendor: DELL Model: RAID5DATA Rev: V1.0 Type: Direct-Access ANSI SCSI revision: 02 Starting timer : 0 0 blk: queue c364ce18, I/O limit 4095Mb (mask 0xffffffff) Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 SCSI device sda: 286714368 512-byte hdwr sectors (146798 MB) Partition check: sda: sda1 sda2 sda3 sda4 < sda5 > Initializing Cryptographic API NET4: Linux TCP/IP 1.0 for NET4.0 IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 348k freed EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal Adding Swap: 2096472k swap-space (priority -1) kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,5), internal journal EXT3-fs: mounted filesystem with ordered data mode. tg3: eth0: Link is up at 100 Mbps, full duplex. tg3: eth0: Flow control is on for TX and on for RX.